
The AirTAC SDAJ32~40 Adjustable Super Slim Cylinder SDAJ40X30-20 is a genuine double-acting COMPACT cylinder (Ø40mm bore) whose extend end-position is set by an external M12×1.25 adjustment screw. You can dial the stroke anywhere from 10 to 30 mm on the machine — no shims, no part change.
The AirTAC SDAJ40X30-20 is a compact double-acting double-rod cylinder featuring an external adjustable extend stop. By turning the R (M12x1.25) screw, you can dial the forward end-position down by 20 mm, yielding a usable extension range of 10 to 30 mm directly on your machine without swapping shims or parts.
Its short riveted body saves valuable axial mounting depth where round-body or larger profile units will not fit. End-of-travel deceleration is handled by a fixed NBR bumper rather than an adjustable air cushion, so for high-energy cycles you should slow the approach or add an external shock absorber. This specific SKU lacks a piston magnet and cannot host sensing switches; adding the -S option enables reed or electronic switch integration.
| Model | Airtac SDAJ32~40 Adjustable Super Slim Cylinder SDAJ40X30-20 |
|---|---|
| Series | SDAJ compact adjustable-stroke cylinder |
| Bore size | Ø40 mm |
| Max stroke | 30 mm |
| Adjustable range | 10 – 30 mm |
| Adjuster thread (R) | M12×1.25 |
| Port size | PT1/8 |
| Acting type | Double acting |
|---|---|
| Rod end thread | M8×1.25 F / M14×1.5 male (B) |
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 500 mm/s |
| Cushion | Fixed NBR bumper (both ends) |
The adjustment screw shortens the extend stroke by up to 20 mm. SDAJ is a double-rod cylinder. Specifications follow the official AirTAC SDAJ datasheet.
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 528 N | 528 N |
| 0.7 MPa | 739 N | — |
| Max (@1.0 MPa) | 108 kgf | |
SDAJ is double-rod: the rear rod that carries the stroke adjuster passes through the rear cover, so both piston faces lose rod area. Push is shown at the annular-area value (conservative), lower than a single-rod SDA push of the same bore. Actual usable force is lower than theoretical due to friction.
| SDAJ | Compact double-acting cylinder with adjustable stroke. |
|---|---|
| 40 | Bore size in mm. |
| ×30 | Maximum stroke length in mm. |
| -20 | Adjustable window (10/20/30/40/50/75/100 mm). |
| S / B | S = magnet; B = male-thread rod (both optional). |
Thread: PT standard. Related SDA-family variants: SDA (fixed stroke), SDAD (double rod), SSA/STA (single acting), SDAT (duplex), SDAW (duplex-end).
Dial in the exact 10 to 30 mm clamping reach on machining fixtures, absorbing part tolerance variations without remachining stops.
Set a precise lower dead stop for light-duty press fits, relying on the fixed NBR bumper to absorb the end shock during repetitive assembly.
Choose this model if your fixture requires frequent on-machine stroke tuning between 10 and 30 mm.
Confirm the 40 mm bore, 30 mm maximum stroke, 20 mm adjust window, and PT1/8 air port match your pneumatic layout. Because this SKU has no -S magnet, position sensing is unavailable unless you specify the magnet option. Note that a plain cylinder does not hold its load on air loss or valve centred—the piston drifts and the fixed bumper only decelerates near the end. For secure load holding without live pressure, install an external rod lock or a pilot-operated check valve.
Quick checklist
The theoretical maximum push force is 128 kgf at 1.0 MPa. The adjustable stop does not alter these force values.
The external M12x1.25 adjuster screw mechanically shortens the extend stroke by up to 20 mm, allowing you to set the forward stop anywhere between 10 and 30 mm. This screw is a mechanical stop, not a mid-stroke lock, and the retract stroke remains full length.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Standard models are processed and dispatched in 3-5 business days.
Most inquiries answered within 7-8 hours.
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.