
The AirTAC SDAJ32~40 Adjustable Super Slim Cylinder SDAJ40X35-30 is a genuine double-acting COMPACT cylinder (Ø40mm bore) whose extend end-position is set by an external M12×1.25 adjustment screw. You can dial the stroke anywhere from 5 to 35 mm on the machine — no shims, no part change.
The AirTAC SDAJ40X35-30 is a compact double-acting double-rod cylinder featuring an external M12x1.25 adjuster screw that lets you dial the extend stop directly on the machine. You can shorten the forward stroke anywhere between 5 and 35 mm without swapping shims or parts, making it highly effective for frequent format changes.
Built with a short riveted body, this unit saves valuable axial mounting depth where larger profile or round-body actuators will not fit. End-of-travel deceleration is handled by a fixed NBR bumper rather than an adjustable air cushion. Note that this specific SKU lacks a piston magnet, so it cannot support reed or electronic sensing without upgrading to the -S variant.
| Model | Airtac SDAJ32~40 Adjustable Super Slim Cylinder SDAJ40X35-30 |
|---|---|
| Series | SDAJ compact adjustable-stroke cylinder |
| Bore size | Ø40 mm |
| Max stroke | 35 mm |
| Adjustable range | 5 – 35 mm |
| Adjuster thread (R) | M12×1.25 |
| Port size | PT1/8 |
| Acting type | Double acting |
|---|---|
| Rod end thread | M8×1.25 F / M14×1.5 male (B) |
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 500 mm/s |
| Cushion | Fixed NBR bumper (both ends) |
The adjustment screw shortens the extend stroke by up to 30 mm. SDAJ is a double-rod cylinder. Specifications follow the official AirTAC SDAJ datasheet.
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 528 N | 528 N |
| 0.7 MPa | 739 N | — |
| Max (@1.0 MPa) | 108 kgf | |
SDAJ is double-rod: the rear rod that carries the stroke adjuster passes through the rear cover, so both piston faces lose rod area. Push is shown at the annular-area value (conservative), lower than a single-rod SDA push of the same bore. Actual usable force is lower than theoretical due to friction.
| SDAJ | Compact double-acting cylinder with adjustable stroke. |
|---|---|
| 40 | Bore size in mm. |
| ×35 | Maximum stroke length in mm. |
| -30 | Adjustable window (10/20/30/40/50/75/100 mm). |
| S / B | S = magnet; B = male-thread rod (both optional). |
Thread: PT standard. Related SDA-family variants: SDA (fixed stroke), SDAD (double rod), SSA/STA (single acting), SDAT (duplex), SDAW (duplex-end).
Dial the extend stop from 5 to 35 mm to accommodate varying raw stock thicknesses on a milling fixture without machining new spacer blocks.
Set a precise lower endpoint for pressing bearings, using the M12x1.25 adjuster to fine-tune insertion depth during prototype runs before finalizing tooling.
Choose this model if your fixture setup requires frequent on-site stroke tuning to hit precise intermediate endpoints.
Confirm the 40 mm bore, 35 mm maximum stroke, 30 mm adjustment window, and PT1/8 air port match your pneumatic layout. This base configuration uses a female M8x1.25 rod-end thread and has no piston magnet. Remember that a standard compact cylinder drifts when air is lost or the valve centers; the fixed bumper only decelerates the stroke end and does not lock the load. Use an external rod lock or pilot-operated check valve if you need to hold a suspended weight safely.
Quick checklist
The theoretical maximum push is 128 kgf at 1.0 MPa. It operates between 0.15 and 1.0 MPa at speeds of 30-500 mm/s.
Turning the external R (M12x1.25) screw shortens the extend endpoint by up to 30 mm, giving a usable forward range of 5 to 35 mm. The retract stroke remains full length. This specific SKU has no piston magnet, so it cannot accept a switch; you must select the -S option to use AirTAC reed or electronic sensors.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Standard models are processed and dispatched in 3-5 business days.
Most inquiries answered within 7-8 hours.
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.