verified AirTAC China Authorized Export Seller shield 100% Genuine AirTAC Parts workspace_premium 1-Year Warranty
appsShop by Modelexpand_more
person shopping_cart Request a QuoteQuote
AirTAC SDAJ Series · Adjustable-Stroke Compact Cylinder

Airtac SDAJ32~40 Adjustable Super Slim Cylinder SDAJ40X40-20

The AirTAC SDAJ32~40 Adjustable Super Slim Cylinder SDAJ40X40-20 is a genuine double-acting COMPACT cylinder (Ø40mm bore) whose extend end-position is set by an external M12×1.25 adjustment screw. You can dial the stroke anywhere from 20 to 40 mm on the machine — no shims, no part change.

  • BoreØ40 mm
  • Max stroke40 mm
  • Adjustable range20–40 mm
  • Adjuster threadM12×1.25
  • Port sizePT1/8
  • CushionFixed NBR bumper (both ends)
$47.89 $55.39Save 13% Standard model — ready in 3-5 business days to process and dispatch
Request a Quote
  • No minimum order. A single piece can be ordered.
  • Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
Compare every SDAJ40 stroke, mounting and version on one page All SDAJ40 codes →
verified Genuine AirTAC workspace_premium 1-year warranty bolt Reply in 7-8 h

About the Airtac SDAJ32~40 Adjustable Super Slim Cylinder SDAJ40X40-20

The AirTAC SDAJ40X40-20 is a double-acting compact cylinder featuring an external M12x1.25 adjustment screw that lets you dial the extend stop down from the 40 mm maximum to any position between 20 and 40 mm directly at the machine. The short riveted body conserves valuable axial mounting depth in tight fixtures where longer profile or round-body units will not fit.

End-of-travel deceleration is handled by a fixed NBR bumper rather than an adjustable air cushion, absorbing shock without requiring tuning. This specific SKU ships without a piston magnet, so it cannot host reed or electronic switches; add the -S option if your application requires position sensing. The 16 mm piston rod uses an M8x1.25 female thread and operates at speeds between 30 and 500 mm/s.

Airtac SDAJ32~40 Adjustable Super Slim Cylinder SDAJ40X40-20 Technical Specifications

ModelAirtac SDAJ32~40 Adjustable Super Slim Cylinder SDAJ40X40-20
SeriesSDAJ compact adjustable-stroke cylinder
Bore sizeØ40 mm
Max stroke40 mm
Adjustable range20 – 40 mm
Adjuster thread (R)M12×1.25
Port sizePT1/8
Acting typeDouble acting
Rod end threadM8×1.25 F / M14×1.5 male (B)
Operating pressure0.15 – 1.0 MPa
Proof pressure1.5 MPa
Temperature-20 to +70 °C
Speed range30 – 500 mm/s
CushionFixed NBR bumper (both ends)

The adjustment screw shortens the extend stroke by up to 20 mm. SDAJ is a double-rod cylinder. Specifications follow the official AirTAC SDAJ datasheet.

Theoretical Output Force (Ø40mm)

PressurePush forcePull force
0.5 MPa528 N528 N
0.7 MPa739 N—
Max (@1.0 MPa)108 kgf

SDAJ is double-rod: the rear rod that carries the stroke adjuster passes through the rear cover, so both piston faces lose rod area. Push is shown at the annular-area value (conservative), lower than a single-rod SDA push of the same bore. Actual usable force is lower than theoretical due to friction.

Model Code: Airtac SDAJ32~40 Adjustable Super Slim Cylinder SDAJ40X40-20

SDAJCompact double-acting cylinder with adjustable stroke.
40Bore size in mm.
×40Maximum stroke length in mm.
-20Adjustable window (10/20/30/40/50/75/100 mm).
S / BS = magnet; B = male-thread rod (both optional).

Thread: PT standard. Related SDA-family variants: SDA (fixed stroke), SDAD (double rod), SSA/STA (single acting), SDAT (duplex), SDAW (duplex-end).

Where the Airtac SDAJ32~40 Adjustable Super Slim Cylinder SDAJ40X40-20 Is Used

precision_manufacturing

Multi-Format Machining Clamps

Dial the extend stop from 20 to 40 mm to secure different raw material widths on a single machining center, avoiding the need to swap out physical spacer shims during production changeovers.

straighten

Trial Positioning for Press Fits

Set the exact 20-40 mm insertion depth for light-duty press fit operations during prototype runs, allowing operators to fine-tune the mechanical stop before finalizing a hard-tooled fixture.

Is the Airtac SDAJ32~40 Adjustable Super Slim Cylinder SDAJ40X40-20 the Right Cylinder?

Choose this 40 mm bore when your setup demands on-site stroke tuning to accommodate multiple product formats without swapping hardware.

Confirm your requirements for a 40 mm bore, 40 mm maximum stroke, and a 20 mm adjustment window via the PT1/8 port. Note that this configuration uses a female rod-end thread and lacks the magnet option. Remember that a standard compact cylinder cannot hold a load if air pressure drops or the valve is centered; the fixed bumper only decelerates near the end of travel and the R screw acts as a mechanical stop, not a brake. For suspended or vertical loads that must resist drifting during air loss, integrate an external rod lock or a pilot-operated check valve.

Quick checklist

  • ✓ Need on-machine stroke fine-tuning?
  • ✓ Target position within 20–40 mm
  • ✓ Force at your working pressure
  • ✓ Access to reach the R adjuster
  • ✓ Magnet (S) for sensors?
Ask an Engineer

Installation & Maintenance Notes

  • check Use clean air filtered to 40µm or finer.
  • check Keep within 0.15 – 1.0 MPa operating pressure.
  • check Lock the M12×1.25 adjuster after setting the stroke.
  • check Avoid side load on the piston rod.
  • check Front/rear covers are riveted — do not dismantle.
  • check Installation by qualified personnel per AirTAC docs.

Airtac SDAJ32~40 Adjustable Super Slim Cylinder SDAJ40X40-20 FAQ

The theoretical maximum push is 128 kgf at 1.0 MPa. It operates on air pressure between 0.15 and 1.0 MPa, with a proof pressure of 1.5 MPa, and functions in temperatures from -20 to +70 C.

Turning the external M12x1.25 R screw mechanically shortens the extend stroke by up to 20 mm, allowing the rod to stop anywhere between 20 and 40 mm. This mechanism sets the end-of-stroke stop and does not alter the output force. It is not a mid-stroke lock; the cylinder cannot hold a load without continuous air pressure, so an external rod lock is required for fail-safe load holding.

verified

Authorized Export Seller

Genuine AirTAC parts produced by AirTAC factory.

workspace_premium

1-Year Warranty

Covers non-human-caused product damage.

local_shipping

Fast Dispatch

Standard models are processed and dispatched in 3-5 business days.

bolt

Fast Reply

Most inquiries answered within 7-8 hours.

Related AirTAC SDAJ Cylinders

Request a Quote for Airtac SDAJ32~40 Adjustable Super Slim Cylinder SDAJ40X40-20

Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.

Thank you. We received your request for SDAJ40X40-20 and will confirm price, stock and lead time — usually within 7-8 hours.

For the fastest response, keep the complete model number above and include a clear photo of the product label. If photo upload is unavailable, email photos to [email protected] with your model number.