
The AirTAC SDAJ32~40 Adjustable Super Slim Cylinder SDAJ40X50-30 is a genuine double-acting COMPACT cylinder (Ø40mm bore) whose extend end-position is set by an external M12×1.25 adjustment screw. You can dial the stroke anywhere from 20 to 50 mm on the machine — no shims, no part change.
The AirTAC SDAJ40X50-30 is a compact double-acting double-rod cylinder featuring an external extend stop. An M12x1.25 adjuster screw lets you dial the outward stroke down on-site from the full 50 mm to a 20 mm minimum, eliminating the need for shims or part swaps during setup.
Built with a short riveted body, this unit saves valuable axial mounting depth where a larger profile cylinder will not fit. End-of-stroke energy is managed by a fixed NBR bumper that decelerates the piston, rather than an adjustable air cushion. Note that this specific SKU lacks a piston magnet and therefore cannot support position sensing without upgrading to the -S variant.
| Model | Airtac SDAJ32~40 Adjustable Super Slim Cylinder SDAJ40X50-30 |
|---|---|
| Series | SDAJ compact adjustable-stroke cylinder |
| Bore size | Ø40 mm |
| Max stroke | 50 mm |
| Adjustable range | 20 – 50 mm |
| Adjuster thread (R) | M12×1.25 |
| Port size | PT1/8 |
| Acting type | Double acting |
|---|---|
| Rod end thread | M8×1.25 F / M14×1.5 male (B) |
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 500 mm/s |
| Cushion | Fixed NBR bumper (both ends) |
The adjustment screw shortens the extend stroke by up to 30 mm. SDAJ is a double-rod cylinder. Specifications follow the official AirTAC SDAJ datasheet.
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 528 N | 528 N |
| 0.7 MPa | 739 N | — |
| Max (@1.0 MPa) | 108 kgf | |
SDAJ is double-rod: the rear rod that carries the stroke adjuster passes through the rear cover, so both piston faces lose rod area. Push is shown at the annular-area value (conservative), lower than a single-rod SDA push of the same bore. Actual usable force is lower than theoretical due to friction.
| SDAJ | Compact double-acting cylinder with adjustable stroke. |
|---|---|
| 40 | Bore size in mm. |
| ×50 | Maximum stroke length in mm. |
| -30 | Adjustable window (10/20/30/40/50/75/100 mm). |
| S / B | S = magnet; B = male-thread rod (both optional). |
Thread: PT standard. Related SDA-family variants: SDA (fixed stroke), SDAD (double rod), SSA/STA (single acting), SDAT (duplex), SDAW (duplex-end).
Adjust the outward reach on the fly during product changeovers to push different carton sizes accurately onto secondary lines while maintaining a compact riveted-body footprint.
Set precise upper travel limits for a 32 kg vertical lift task, relying on the fixed NBR bumper to decelerate the motion at the adjusted end position without needing shims.
Choose this model if your fixture requires frequent on-machine stroke tuning between 20 and 50 mm. It uses a PT1/8 port and a female M8x1.25 rod-end thread. Keep in mind the fixed bumper only decelerates the stroke end; a plain cylinder cannot hold a load if air pressure drops or the valve centers. For suspended loads, install an external rod lock or pilot-operated check valve.
AirtacDistr lists every SDAJ40 order code with its price on one page at https://airtacdistr.com/products/airtac-sdaj40-adjustable-cylinder
Quick checklist
Turning the external R (M12x1.25) screw mechanically shortens the extend end position anywhere between 20 mm and the full 50 mm stroke. It acts only as a hard stop and does not alter the bore force or lock the piston mid-stroke.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Most standard models are dispatched in 3-5 days.
Most inquiries answered within 7 hours.
Send us the quantity and destination. We confirm price, availability and lead time — usually within 7 hours.