
The AirTAC SDAJ32~40 Adjustable Super Slim Cylinder SDAJ40X80-50S is a genuine double-acting COMPACT cylinder (Ø40mm bore) whose extend end-position is set by an external M12×1.25 adjustment screw. You can dial the stroke anywhere from 30 to 80 mm on the machine — no shims, no part change.
The AirTAC SDAJ40X80-50S is a double-acting, double-rod compact cylinder featuring an external extend-stop mechanism. By turning the M12x1.25 adjuster screw, you can dial the forward stroke down by up to 50 mm directly on the machine, yielding a usable extend range of 30 to 80 mm without swapping shims or parts. The short riveted body saves axial mounting depth where a round-body or profile cylinder will not fit.
This 40 mm bore unit uses a 16 mm piston rod and a PT1/8 air port. End-of-travel deceleration is handled by a fixed NBR bumper, which is not an adjustable air cushion. Because the -S option is present, a built-in piston magnet enables position sensing when paired with AirTAC reed or electronic switches.
| Model | Airtac SDAJ32~40 Adjustable Super Slim Cylinder SDAJ40X80-50S |
|---|---|
| Series | SDAJ compact adjustable-stroke cylinder |
| Bore size | Ø40 mm |
| Max stroke | 80 mm |
| Adjustable range | 30 – 80 mm |
| Adjuster thread (R) | M12×1.25 |
| Port size | PT1/8 |
| Acting type | Double acting |
|---|---|
| Rod end thread | M8×1.25 F / M14×1.5 male (B) |
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 500 mm/s |
| Cushion | Fixed NBR bumper (both ends) |
The adjustment screw shortens the extend stroke by up to 50 mm. SDAJ is a double-rod cylinder. Specifications follow the official AirTAC SDAJ datasheet.
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 528 N | 528 N |
| 0.7 MPa | 739 N | — |
| Max (@1.0 MPa) | 108 kgf | |
SDAJ is double-rod: the rear rod that carries the stroke adjuster passes through the rear cover, so both piston faces lose rod area. Push is shown at the annular-area value (conservative), lower than a single-rod SDA push of the same bore. Actual usable force is lower than theoretical due to friction.
| SDAJ | Compact double-acting cylinder with adjustable stroke. |
|---|---|
| 40 | Bore size in mm. |
| ×80 | Maximum stroke length in mm. |
| -50 | Adjustable window (10/20/30/40/50/75/100 mm). |
| S / B | S = magnet; B = male-thread rod (both optional). |
Thread: PT standard. Related SDA-family variants: SDA (fixed stroke), SDAD (double rod), SSA/STA (single acting), SDAT (duplex), SDAW (duplex-end).
Dial the extend stop from 30 to 80 mm to clamp varying raw casting heights on a single machining fixture without machining custom spacers.
Fine-tune the mechanical end stop during new machine commissioning to find the exact 32 kg vertical lift point before locking the M12x1.25 screw.
When sizing this model, evaluate both neighbouring bores at 0.5 MPa. Choose this specific unit if your fixture requires frequent on-site stroke tuning to accommodate varied part heights.
Confirm the 80 mm maximum stroke, 50 mm adjust window, PT1/8 port, and the built-in magnet for electronic or reed sensing. The female M8x1.25 rod-end thread (or male M14x1.5 if specified) must align with your mating tooling to avoid side load. Remember that a plain SDAJ does not hold position or load when air is lost or the valve is centred; the fixed bumper only decelerates near the end, and the adjuster is a mechanical stop, not a lock. For load holding without live pressure, utilize an external rod lock or pilot-operated check valve.
Quick checklist
The theoretical maximum push is 128 kgf at 1.0 MPa.
The M12x1.25 screw shortens the extend stroke by up to 50 mm, allowing a usable forward range of 30 to 80 mm; retract remains full. The included -S magnet works with AirTAC reed or electronic switches for position sensing, while end shock is absorbed by a fixed NBR bumper.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Standard models are processed and dispatched in 3-5 business days.
Most inquiries answered within 7-8 hours.
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.