The AirTAC SDAW Dual-Axis Compound Multi-Position Cylinder SDAW32X20X10SB is a genuine COMPACT duplex-end cylinder (Ø32mm bore) with a 0 mm and a 0 mm section combined at the rod end. Switching the two chambers parks the rod at 0, 0 and 0 mm — three repeatable stops without an external stopper.
The SDAW32X20X10SB is a double-acting compact duplex-end multi-position cylinder with a 32 mm bore and an integrated rod-end section. The rod can be parked at 0, 20, or 30 mm simply by switching the two air chambers, so one actuator replaces what would otherwise be two cylinders piped in sequence.
The duplex-end layout adds positions, not thrust: output equals a single 32 mm SDA, delivering 402.1 N push at 0.5 MPa. End-of-travel damping is a fixed NBR bumper, and body sensor grooves are ready for AirTAC reed or electronic switches once the -S magnet is present, which this model carries. Porting is PT1/8 and the rod thread is male M10x1.25 per the B suffix.
| Model | Airtac SDAW Dual-Axis Compound Multi-Position Cylinder SDAW32X20X10SB |
|---|---|
| Series | SDAW compact duplex-end (multi-position) cylinder |
| Bore size | Ø32 mm |
| Stroke 1 / Stroke 2 | 0 / 0 mm |
| Fixed positions | 0 / 0 / 0 mm |
| Port size | PT1/8 |
| Rod end thread | M6×1.0 F / M10×1.25 male (B) |
| Acting type | Double acting, duplex-end |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 500 mm/s |
| Cushion | Fixed NBR bumper |
| Stroke rule | Stroke 1 + Stroke 2 ≤ standard max |
Stroke 1 + Stroke 2 must not exceed the standard stroke maximum for the bore. Confirm the exact stop sequence against the AirTAC SDAW datasheet before wiring the valves.
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 402 N | 346 N |
| 0.7 MPa | 563 N | — |
| Max (@1.0 MPa) | 82 kgf | |
Force is set by the single piston area (same as an SDA of this bore) — the duplex-end design adds positions, not thrust. Actual usable force is lower than theoretical.
| SDAW | Compact duplex-end (multi-position) cylinder. |
|---|---|
| 32 | Bore size in mm. |
| ×0 | Stroke 1 (first section) in mm. |
| ×0 | Stroke 2 (rod-end section) in mm. |
| S / B | S = magnet; B = male-thread rod (both optional). |
Thread: PT standard. Related: SDAT (duplex multi-position), SDA (single position), SDAD (double rod), SDAJ (adjustable stroke).
A bend line on a packaging flap needs three defined rest points along the press stroke; the 20 mm and 30 mm stops select light or deep flaps with 402.1 N of push.
Rotating tray carriers index to two pin heights plus retracted on a small assembly carousel; the rod-end duplex section keeps the whole mechanism inside a short header plate.
A bench fixture lowers a gauge block to a near-touch position at 20 mm and full contact at 30 mm, with switch feedback confirming each stop on the magnet.
For force sizing, one bore down at 25 mm gives 245.4 N push at 0.5 MPa; one bore up at 40 mm gives 628.3 N. If the load sits between those figures, stay with 32 mm. Reaching all three stops (0 / 20 / 30 mm) requires two solenoid lines, so budget the valve positions accordingly. Note that a plain SDAW will not hold the rod or its load if air pressure is lost or valves are centred; use an external locking or clamping device for true load holding. Choose SDAW when the extra section should sit at the rod end; pick SDAT if a stacked duplex body suits your envelope, or plain SDA for a single stop. Confirm bore, S1 = 20, S2 = 10, PT1/8 port, the S magnet option, and the male rod thread against the datasheet before ordering.
Quick checklist
Stops are 0 / 20 / 30 mm, selected by the two chambers. Force comes from one 32 mm piston area only: 402.1 N push and 345.6 N pull at 0.5 MPa, 563.0 N push at 0.7 MPa, and a maximum push of 82 kgf at 1.0 MPa. It is double-acting throughout, speed range 30-500 mm/s.
No. Both give multiple stops, but the SDAT stacks the second piston section behind the first, while SDAW attaches it at the rod end, changing the collapsed length and mounting geometry. On this model the S option magnet works with AirTAC reed or electronic switches to verify each of the three positions.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Standard models are processed and dispatched in 3-5 business days.
Most inquiries answered within 7-8 hours.
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.