
The AirTAC SEJ Adjustable Cylinder SEJ100X100-100S is a genuine double-acting ISO 15552 double-rod cylinder with a mechanically ADJUSTABLE stroke: a back-rod stop screw lets you fine-tune the retract end over a 100mm window, so this Ø100mm unit covers an effective stroke of 0–100mm without changing cylinders. Force is equal in both directions.
The AirTAC SEJ100X100-100S is a double-acting, double-rod ISO 15552 profile cylinder with a 100mm adjustment window. A rod exits both ends, yielding identical annulus areas so thrust is equal both ways: about 3681 N each way at 0.5 MPa. The back-rod stop screw lets you dial the retract end over the full 100mm window, giving an effective stroke range of 0 to 100mm.
This extruded aluminum barrel unit runs at 30-800 mm/s and carries the -S magnet for CMSE reed or DMSE electronic sensors. Adjustable air cushions at both ends decelerate the load near stroke end, while the M20x1.5 rod ends and PT1/2 ports handle the 25mm rod and 751 kgf max load.
| Model | Airtac SEJ Adjustable Cylinder SEJ100X100-100S |
|---|---|
| Series | SEJ ISO 15552 adjustable-stroke cylinder |
| Bore size | Ø100 mm |
| Nominal stroke | 100 mm |
| Adjustment window | 100 mm (0–100 mm) |
| Configuration | Double rod, double acting |
| Port size | PT1/2 |
| Rod thread | M20×1.5 |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 36 mm |
Specifications follow the official AirTAC SEJ datasheet and ISO 15552 / VDMA 24562 dimensions. The adjustment screw shortens the retract end only; do not exceed the 100mm window. Port options: PT (standard) / G (BSPP).
| Pressure | Force (both directions) |
|---|---|
| 0.5 MPa | 3682 N |
| 0.7 MPa | 5154 N |
| Max (@1.0 MPa) | 751 kgf |
A rod exits both ends, so extend and retract force are identical. Actual usable force is lower than theoretical; size with a safety margin.
| SEJ | ISO 15552 double-rod double-acting cylinder with adjustable stroke. |
|---|---|
| 100 | Bore size in mm. |
| ×100 | Nominal stroke length in mm. |
| -100 | Adjustment stroke window in mm (options: 10/20/30/40/50/75/100). |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting (SEJ): Basic, LB, FA, TC, FTC, TCM1, TCM2. Related: SED (double rod, fixed stroke), SE (single rod).
Dial the 0-100mm retract window to match varying metal blank thicknesses on a stamping press, leveraging the 5153 N both-way force to pull the feed gripper.
Adjust the mechanical stop on the fly to handle different pallet heights without swapping hardware, using the equal double-rod thrust to push loads smoothly.
Fine-tune the trial position for a bar feeder arm during commissioning, locking the back-rod stop screw once the 3681 N extraction pull is perfectly timed.
The 100mm adjustment window covers a 0-100mm effective range, ideal for machines needing variable-stop positions or rapid part-height changeovers. If 5153 N at 0.7 MPa is excessive, step down to the 80mm bore (2268 N at 0.5 MPa); if insufficient, move up to the 125mm bore (5734 N at 0.5 MPa). If the end position never varies, a fixed-stroke SED avoids the stop-screw setup. The stop screw and cushions only set the mechanical end and decelerate the load; they do not hold position on air loss, so use an external rod lock for fail-safe clamping. As a dimensionally interchangeable ISO 15552 unit, match the 100mm bore, 100mm stroke, PT1/2 port, and mounting from the SEJ set (Basic, FA, LB, TC, FTC, TCM1, TCM2).
Quick checklist
The back-rod stop screw provides a 100mm adjustment window, allowing the effective retract stroke to be dialed anywhere from 0 to 100mm. You lock the stop screw mechanically after setting the exact end position.
Because the rod exits both ends, the annulus area is identical in both directions. The equal both-way force is 3681 N at 0.5 MPa, 5153 N at 0.7 MPa, and the maximum is 751 kgf at 1.0 MPa.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Standard models are processed and dispatched in 3-5 business days.
Most inquiries answered within 7-8 hours.
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.