
The AirTAC SEJ Adjustable Cylinder SEJ100X100-50S is a genuine double-acting ISO 15552 double-rod cylinder with a mechanically ADJUSTABLE stroke: a back-rod stop screw lets you fine-tune the retract end over a 50mm window, so this Ø100mm unit covers an effective stroke of 50–100mm without changing cylinders. Force is equal in both directions.
The AirTAC SEJ100X100-50S is a double-acting, double-rod ISO 15552 profile cylinder with an adjustable stroke. A rod exits both ends, ensuring equal force and speed in both directions. The retract stroke is mechanically adjustable via a stop screw on the back rod over a 50 mm window, giving an effective stroke range of 50 to 100 mm.
Because the annulus area is identical on both sides, you use the same force figure for extend and retract. The back rod can carry a cam for position sensing. The included -S magnet enables electronic position tracking using DMSE sensors or reed switches like CMSE. The extruded aluminum barrel has no external tie rods, and the adjustable air cushions at both ends decelerate the load near the stroke ends without acting as a lock.
| Model | Airtac SEJ Adjustable Cylinder SEJ100X100-50S |
|---|---|
| Series | SEJ ISO 15552 adjustable-stroke cylinder |
| Bore size | Ø100 mm |
| Nominal stroke | 100 mm |
| Adjustment window | 50 mm (50–100 mm) |
| Configuration | Double rod, double acting |
| Port size | PT1/2 |
| Rod thread | M20×1.5 |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 36 mm |
Specifications follow the official AirTAC SEJ datasheet and ISO 15552 / VDMA 24562 dimensions. The adjustment screw shortens the retract end only; do not exceed the 50mm window. Port options: PT (standard) / G (BSPP).
| Pressure | Force (both directions) |
|---|---|
| 0.5 MPa | 3682 N |
| 0.7 MPa | 5154 N |
| Max (@1.0 MPa) | 751 kgf |
A rod exits both ends, so extend and retract force are identical. Actual usable force is lower than theoretical; size with a safety margin.
| SEJ | ISO 15552 double-rod double-acting cylinder with adjustable stroke. |
|---|---|
| 100 | Bore size in mm. |
| ×100 | Nominal stroke length in mm. |
| -50 | Adjustment stroke window in mm (options: 10/20/30/40/50/75/100). |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting (SEJ): Basic, LB, FA, TC, FTC, TCM1, TCM2. Related: SED (double rod, fixed stroke), SE (single rod).
Provides 5153 N both ways at 0.7 MPa for assembly presses. The 50 mm window lets operators dial in the exact 50-100 mm crush depth for different material thicknesses without swapping hardware.
Handles heavy pallet stops in packaging lines.
Controls heavy web tensioning arms in paper converting. The rear rod supports a cam for DMSE sensors, and the adjustable end precisely sets the 50 mm tensioning range.
This 100 mm bore provides 3681 N both ways at 0.5 MPa. If your load requires less force, the 80 mm bore gives 2268 N. If you need more power, the 125 mm bore offers 5734 N. The 50 mm adjustment window is ideal for fine-tuning a precise end position during commissioning without machining new hard stops.
If your stroke never changes, a fixed-stroke SED is sufficient. Note that this plain SEJ cylinder does not hold position on air loss; the cushion and stop screw only set the mechanical end. For fail-safe holding, use an external rod lock or BSED. To replace an ISO 15552 cylinder, match the 100 mm bore, 100 mm nominal stroke, PT1/2 port, and mounting choice from Basic, FA, LB, TC, FTC, TCM1, or TCM2.
Quick checklist
A stop screw on the back rod mechanically shortens the retract stroke over a 50 mm window. You can dial the effective stroke from 50 mm up to the nominal 100 mm. Once set, lock the screw to hold your exact end position.
Because it is a double-rod cylinder, force is equal both ways: 3681 N at 0.5 MPa, 5153 N at 0.7 MPa, and a maximum of 751 kgf at 1.0 MPa. It operates at speeds of 30-800 mm/s.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Standard models are processed and dispatched in 3-5 business days.
Most inquiries answered within 7-8 hours.
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.