
The AirTAC SEJ Adjustable Cylinder SEJ100X120-75S is a genuine double-acting ISO 15552 double-rod cylinder with a mechanically ADJUSTABLE stroke: a back-rod stop screw lets you fine-tune the retract end over a 75mm window, so this Ø100mm unit covers an effective stroke of 45–120mm without changing cylinders. Force is equal in both directions.
The AirTAC SEJ100X120-75S is a double-acting, double-rod ISO 15552 profile cylinder featuring a 75 mm mechanical stroke-adjustment window. You can dial the retract end-position anywhere in an effective 45 to 120 mm range. Because a rod exits both ends, the annular area is symmetrical, delivering an equal 3681 N of drive force each way at 0.5 MPa.
A stop screw on the back rod sets the exact retract limit, which you lock down after fine-tuning the machine. This 100 mm bore uses a PT1/2 port and a Ø25 mm rod with an M20x1.5 thread. The integrated -S magnet enables position detection with CMSE reed or DMSE electronic sensors, while field-adjustable air cushions at both ends manage kinetic energy.
| Model | Airtac SEJ Adjustable Cylinder SEJ100X120-75S |
|---|---|
| Series | SEJ ISO 15552 adjustable-stroke cylinder |
| Bore size | Ø100 mm |
| Nominal stroke | 120 mm |
| Adjustment window | 75 mm (45–120 mm) |
| Configuration | Double rod, double acting |
| Port size | PT1/2 |
| Rod thread | M20×1.5 |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 36 mm |
Specifications follow the official AirTAC SEJ datasheet and ISO 15552 / VDMA 24562 dimensions. The adjustment screw shortens the retract end only; do not exceed the 75mm window. Port options: PT (standard) / G (BSPP).
| Pressure | Force (both directions) |
|---|---|
| 0.5 MPa | 3682 N |
| 0.7 MPa | 5154 N |
| Max (@1.0 MPa) | 751 kgf |
A rod exits both ends, so extend and retract force are identical. Actual usable force is lower than theoretical; size with a safety margin.
| SEJ | ISO 15552 double-rod double-acting cylinder with adjustable stroke. |
|---|---|
| 100 | Bore size in mm. |
| ×120 | Nominal stroke length in mm. |
| -75 | Adjustment stroke window in mm (options: 10/20/30/40/50/75/100). |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting (SEJ): Basic, LB, FA, TC, FTC, TCM1, TCM2. Related: SED (double rod, fixed stroke), SE (single rod).
Adjust the mechanical end-stop on the fly for different package sizes on a conveyor line without swapping hardware, leveraging the equal both-way thrust.
Fine-tune the 45 to 120 mm effective stroke during R&D prototype machine commissioning, locking the back-rod screw once the optimal travel is found.
Verify that the 75 mm adjustment window comfortably spans your required end-position variance. If 5153 N at 0.7 MPa is excessive, step down to the 80 mm bore (2268 N at 0.5 MPa); if you need more thrust, the 125 mm bore provides 5734 N at 0.5 MPa. If your machine never requires stroke changes, a fixed-stroke SED saves length and cost.
For any fail-safe load holding during air loss, note that the adjustable stop screw and air cushions only set the mechanical end and decelerate near stroke end; they do not lock the rod. You must add an external rod lock like a BSED. When replacing an ISO 15552 unit, match the 100 mm bore, 120 mm nominal stroke, PT1/2 port, and your mounting choice from Basic, FA, LB, TC, FTC, TCM1, or TCM2.
Quick checklist
The 75 mm adjustment window allows you to mechanically shorten the retract stroke from the 120 mm nominal down to 45 mm. You set the exact end-position using a stop screw on the back rod and lock it in place.
Because it is a double-rod cylinder, force is equal in both directions. It provides 3681 N at 0.5 MPa, 5153 N at 0.7 MPa, and a maximum of 751 kgf at 1.0 MPa.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Standard models are processed and dispatched in 3-5 business days.
Most inquiries answered within 7-8 hours.
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.