
The AirTAC SEJ Adjustable Cylinder SEJ100X125-40S is a genuine double-acting ISO 15552 double-rod cylinder with a mechanically ADJUSTABLE stroke: a back-rod stop screw lets you fine-tune the retract end over a 40mm window, so this Ø100mm unit covers an effective stroke of 85–125mm without changing cylinders. Force is equal in both directions.
The AirTAC SEJ100X125-40S is a double-acting, double-rod ISO 15552 profile cylinder featuring a 40mm adjustable stroke window. A rod exits both ends, yielding identical annulus areas so thrust is equal in both directions at 3681N each way at 0.5MPa. The retract stroke dials in from 85mm up to the 125mm nominal length.
You set the exact end position via a mechanical stop screw on the back rod, then lock it down for repeatable machine cycles. The extruded aluminum barrel omits external tie rods for a clean ISO 15552互换 build. A factory-installed magnet (-S) supports CMSE reed and DMSE electronic sensors for end-of-stroke signaling.
| Model | Airtac SEJ Adjustable Cylinder SEJ100X125-40S |
|---|---|
| Series | SEJ ISO 15552 adjustable-stroke cylinder |
| Bore size | Ø100 mm |
| Nominal stroke | 125 mm |
| Adjustment window | 40 mm (85–125 mm) |
| Configuration | Double rod, double acting |
| Port size | PT1/2 |
| Rod thread | M20×1.5 |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 36 mm |
Specifications follow the official AirTAC SEJ datasheet and ISO 15552 / VDMA 24562 dimensions. The adjustment screw shortens the retract end only; do not exceed the 40mm window. Port options: PT (standard) / G (BSPP).
| Pressure | Force (both directions) |
|---|---|
| 0.5 MPa | 3682 N |
| 0.7 MPa | 5154 N |
| Max (@1.0 MPa) | 751 kgf |
A rod exits both ends, so extend and retract force are identical. Actual usable force is lower than theoretical; size with a safety margin.
| SEJ | ISO 15552 double-rod double-acting cylinder with adjustable stroke. |
|---|---|
| 100 | Bore size in mm. |
| ×125 | Nominal stroke length in mm. |
| -40 | Adjustment stroke window in mm (options: 10/20/30/40/50/75/100). |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting (SEJ): Basic, LB, FA, TC, FTC, TCM1, TCM2. Related: SED (double rod, fixed stroke), SE (single rod).
Delivers 3681N both ways to seat bearings. The 40mm window lets you dial the exact 85-125mm crush depth without swapping hardware during commissioning.
Provides 5153N at 0.7MPa for metal forming. Adjust the retract stop to match varying material thicknesses precisely on the fly.
Handles carton folding at 751kgf max. Shift the end position 40mm to accommodate different box heights quickly without re-engineering the line.
Verify the 40mm window covers your fine-tuning range; the effective stroke spans 85-125mm. If 5153N at 0.7MPa is excessive, step down to the 80mm bore (3175N both ways). If your process needs more push, move up to the 125mm bore (8028N). For fixed-position tasks without commissioning tweaks, a standard SED cylinder is sufficient.
This unit does not hold position on air loss; the adjustable cushion and stop screw only set the mechanical end and decelerate near stroke end. For fail-safe holding, specify an external rod lock. The PT1/2 port and M20x1.5 rod thread match standard ISO 15552 mounting interfaces (Basic, FA, LB, TC, FTC, TCM1, TCM2).
Quick checklist
The 40mm window lets you dial the retract stroke from 85mm up to the 125mm nominal length. You set the mechanical stop screw on the back rod to the exact position and lock it.
Because the rod exits both ends, force is equal in both directions: 3681N at 0.5MPa, 5153N at 0.7MPa, and a maximum of 751kgf at 1.0MPa.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Standard models are processed and dispatched in 3-5 business days.
Most inquiries answered within 7-8 hours.
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.