
The AirTAC SEJ Adjustable Cylinder SEJ100X150-20S is a genuine double-acting ISO 15552 double-rod cylinder with a mechanically ADJUSTABLE stroke: a back-rod stop screw lets you fine-tune the retract end over a 20mm window, so this Ø100mm unit covers an effective stroke of 130–150mm without changing cylinders. Force is equal in both directions.
The AirTAC SEJ100X150-20S is a double-acting, double-rod ISO 15552 profile cylinder with a 20mm adjustable stroke window, yielding an effective travel of 130-150mm. A rod exits both ends, meaning the annulus area is identical in both directions.
You dial in the retract end position using a mechanical stop screw on the back rod, then lock it down. This cylinder includes a standard magnet for position sensing. The extruded aluminum barrel carries no external tie rods, and adjustable air cushions at both ends absorb kinetic energy near stroke end.
| Model | Airtac SEJ Adjustable Cylinder SEJ100X150-20S |
|---|---|
| Series | SEJ ISO 15552 adjustable-stroke cylinder |
| Bore size | Ø100 mm |
| Nominal stroke | 150 mm |
| Adjustment window | 20 mm (130–150 mm) |
| Configuration | Double rod, double acting |
| Port size | PT1/2 |
| Rod thread | M20×1.5 |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 36 mm |
Specifications follow the official AirTAC SEJ datasheet and ISO 15552 / VDMA 24562 dimensions. The adjustment screw shortens the retract end only; do not exceed the 20mm window. Port options: PT (standard) / G (BSPP).
| Pressure | Force (both directions) |
|---|---|
| 0.5 MPa | 3682 N |
| 0.7 MPa | 5154 N |
| Max (@1.0 MPa) | 751 kgf |
A rod exits both ends, so extend and retract force are identical. Actual usable force is lower than theoretical; size with a safety margin.
| SEJ | ISO 15552 double-rod double-acting cylinder with adjustable stroke. |
|---|---|
| 100 | Bore size in mm. |
| ×150 | Nominal stroke length in mm. |
| -20 | Adjustment stroke window in mm (options: 10/20/30/40/50/75/100). |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting (SEJ): Basic, LB, FA, TC, FTC, TCM1, TCM2. Related: SED (double rod, fixed stroke), SE (single rod).
Dial the 20mm retract window to match varying die heights during press setup. The 5153 N both-way force at 0.7 MPa ensures positive clamping and lifting without sag.
Fine-tune the stop position for different pallet sizes on a conveyor line. The double-rod design provides 3681 N of stopping force while resisting rotational torque.
Adjust the retract stroke on the fly to pick parts from varying depths. The symmetrical rod design ensures consistent extend and retract speeds for smooth transfer.
Verify the 20mm adjustment window covers your fine-tuning range before ordering. If you need less thrust, the 80mm bore provides 2268 N at 0.5 MPa; stepping up to 125mm yields 5734 N. For fixed end positions that never change, a standard SED double-rod cylinder is sufficient. This cylinder uses a PT1/2 port and a Ø25mm rod with an M20x1.5 thread. Since the stroke is under 300mm, side-loading is less critical, but external guides are still recommended for heavy loads. The air cushion decelerates the load but does not hold position on air loss; use an external rod lock for fail-safe holding.
Quick checklist
A stop screw on the rear rod mechanically limits the retract stroke. For the SEJ100X150-20S, you can adjust the effective stroke from 130mm up to 150mm. You set the exact end position during commissioning and lock the screw.
Because it is a double-rod cylinder, force is identical in both directions. It generates 3681 N at 0.5 MPa, 5153 N at 0.7 MPa, and a maximum of 751 kgf at 1.0 MPa.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Standard models are processed and dispatched in 3-5 business days.
Most inquiries answered within 7-8 hours.
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.