
The AirTAC SEJ Adjustable Cylinder SEJ100X400-100S is a genuine double-acting ISO 15552 double-rod cylinder with a mechanically ADJUSTABLE stroke: a back-rod stop screw lets you fine-tune the retract end over a 100mm window, so this Ø100mm unit covers an effective stroke of 300–400mm without changing cylinders. Force is equal in both directions.
The AirTAC SEJ100X400-100S is a double-acting, double-rod ISO 15552 profile cylinder offering a 100 mm adjustable stroke window. You can dial the retract end-position from 300 mm up to the 400 mm nominal stroke, letting you fine-tune machine stops without swapping hardware. A rod exits both ends, yielding identical extend and retract forces of 3681 N at 0.5 MPa.
Because the rear rod features a mechanical stop screw, you lock the exact end-position after commissioning. The -S magnet enables position sensing with CMSE reed or DMSE electronic switches. Adjustable air cushions at both ends decelerate the heavy 100 mm bore payload smoothly.
| Model | Airtac SEJ Adjustable Cylinder SEJ100X400-100S |
|---|---|
| Series | SEJ ISO 15552 adjustable-stroke cylinder |
| Bore size | Ø100 mm |
| Nominal stroke | 400 mm |
| Adjustment window | 100 mm (300–400 mm) |
| Configuration | Double rod, double acting |
| Port size | PT1/2 |
| Rod thread | M20×1.5 |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 36 mm |
Specifications follow the official AirTAC SEJ datasheet and ISO 15552 / VDMA 24562 dimensions. The adjustment screw shortens the retract end only; do not exceed the 100mm window. Port options: PT (standard) / G (BSPP).
| Pressure | Force (both directions) |
|---|---|
| 0.5 MPa | 3682 N |
| 0.7 MPa | 5154 N |
| Max (@1.0 MPa) | 751 kgf |
A rod exits both ends, so extend and retract force are identical. Actual usable force is lower than theoretical; size with a safety margin.
| SEJ | ISO 15552 double-rod double-acting cylinder with adjustable stroke. |
|---|---|
| 100 | Bore size in mm. |
| ×400 | Nominal stroke length in mm. |
| -100 | Adjustment stroke window in mm (options: 10/20/30/40/50/75/100). |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting (SEJ): Basic, LB, FA, TC, FTC, TCM1, TCM2. Related: SED (double rod, fixed stroke), SE (single rod).
Dial the 100 mm window to match varying material thicknesses in a stamping press, using the 5153 N retract force to consistently pull the die back to a precise 300-400 mm stop.
Adjust the retract end-position on the fly when switching between different pallet heights, relying on the equal both-way force to lift and lower heavy 100 mm bore fixtures smoothly.
Fine-tune the mechanical end stop during metal bending trials, locking the back-rod screw once the 300-400 mm stroke range hits the exact forming depth for the part.
Verify the 100 mm adjustment window covers your required positioning range. If you need less force, stepping down to the 80 mm bore yields 2268 N at 0.5 MPa; stepping up to the 125 mm bore provides 5734 N. If you never need to vary the stroke, a fixed-stroke SED cylinder simplifies the setup. Note that the air cushion and stop screw only set the mechanical end and decelerate near stroke end; they do not hold position on air loss. For fail-safe holding, use an external rod lock.
At 400 mm stroke, the extended rod is susceptible to side loads; ensure external guides support the payload to prevent binding. This ISO 15552 dimensionally interchangeable cylinder uses a PT1/2 port, a 25 mm rod, and accepts Basic, FA, LB, TC, FTC, TCM1, or TCM2 mounts.
Quick checklist
The SEJ100X400-100S features a 100 mm adjustment window on the retract end. You can mechanically dial the effective stroke anywhere from 300 mm up to the nominal 400 mm via the back-rod stop screw, then lock it in place.
Because it is a double-rod cylinder, the force is identical in both directions. It outputs 3681 N at 0.5 MPa, 5153 N at 0.7 MPa, and a maximum of 751 kgf at 1.0 MPa.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Standard models are processed and dispatched in 3-5 business days.
Most inquiries answered within 7-8 hours.
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.