
The AirTAC SEJ Adjustable Cylinder SEJ32X136-10S is a genuine double-acting ISO 15552 double-rod cylinder with a mechanically ADJUSTABLE stroke: a back-rod stop screw lets you fine-tune the retract end over a 10mm window, so this Ø32mm unit covers an effective stroke of 126–136mm without changing cylinders. Force is equal in both directions.
The AirTAC SEJ32X136-10S is a double-acting, double-rod ISO 15552 profile cylinder. A rod exits both ends, yielding identical annulus areas so output force is equal in both directions at 345 N each way at 0.5 MPa. The retract stroke is mechanically adjustable via a stop screw on the back rod, covering a 10 mm window to yield an effective stroke range of 126-136 mm.
This extruded aluminum barrel design omits external tie rods for a clean profile. It includes field-adjustable air cushions at both ends to decelerate the load near stroke end. The -S magnet option enables position detection with CMSE reed or DMSE electronic sensors.
| Model | Airtac SEJ Adjustable Cylinder SEJ32X136-10S |
|---|---|
| Series | SEJ ISO 15552 adjustable-stroke cylinder |
| Bore size | Ø32 mm |
| Nominal stroke | 136 mm |
| Adjustment window | 10 mm (126–136 mm) |
| Configuration | Double rod, double acting |
| Port size | PT1/8 |
| Rod thread | M10×1.25 |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 27 mm |
Specifications follow the official AirTAC SEJ datasheet and ISO 15552 / VDMA 24562 dimensions. The adjustment screw shortens the retract end only; do not exceed the 10mm window. Port options: PT (standard) / G (BSPP).
| Pressure | Force (both directions) |
|---|---|
| 0.5 MPa | 346 N |
| 0.7 MPa | 484 N |
| Max (@1.0 MPa) | 70 kgf |
A rod exits both ends, so extend and retract force are identical. Actual usable force is lower than theoretical; size with a safety margin.
| SEJ | ISO 15552 double-rod double-acting cylinder with adjustable stroke. |
|---|---|
| 32 | Bore size in mm. |
| ×136 | Nominal stroke length in mm. |
| -10 | Adjustment stroke window in mm (options: 10/20/30/40/50/75/100). |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting (SEJ): Basic, LB, FA, TC, FTC, TCM1, TCM2. Related: SED (double rod, fixed stroke), SE (single rod).
Dial in the exact 126-136 mm retract position during machine commissioning to match varying part widths, utilizing the 345 N both-way force for secure gripping.
Quickly adjust the end stop by up to 10 mm when switching the production line to a new product height, avoiding hardware changes on the pneumatic press.
Use the back-rod stop screw to fine-tune the end position during prototype tooling setup, locking the 12 mm rod precisely where the 483 N @0.7 MPa force is needed.
Verify the 10 mm adjustment window provides enough tuning range for your end-position fine-tuning. If you need less force, the next bore down is 32 mm (this is the minimum size), but if you need more power, stepping up to the 40 mm bore yields 528 N both ways at 0.5 MPa. If your machine requires a fixed end position with no commissioning dial-in, a standard SED double-rod cylinder is sufficient.
This cylinder does not hold position on air loss; the stop screw and air cushions only set the mechanical end and decelerate the load, so specify an external rod lock for fail-safe holding. Because the 136 mm stroke is under 300 mm, side-load stress is manageable, but always align the rod thread (M10x1.25) precisely with your external guides. Ensure your ISO 15552 replacement matches the PT1/8 port, 32 mm bore, and mounting set (Basic, FA, LB, TC, FTC, TCM1, TCM2).
Quick checklist
The retract stroke is adjustable over a 10 mm window via a mechanical stop screw on the back rod. For a 136 mm nominal stroke, this gives an effective stroke range of 126-136 mm. You lock the screw after setting the exact end position.
Because the rod exits both ends, force is identical in both directions. It generates 345 N at 0.5 MPa, 483 N at 0.7 MPa, and a maximum of 70 kgf at 1.0 MPa.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Most standard models are dispatched in 3-5 days.
Most inquiries answered within 7 hours.
Send us the quantity and destination. We confirm price, availability and lead time — usually within 7 hours.