
The AirTAC SEJ Adjustable Cylinder SEJ32X160-40 is a genuine double-acting ISO 15552 double-rod cylinder with a mechanically ADJUSTABLE stroke: a back-rod stop screw lets you fine-tune the retract end over a 40mm window, so this Ø32mm unit covers an effective stroke of 120–160mm without changing cylinders. Force is equal in both directions.
The AirTAC SEJ32X160-40 is a double-acting, double-rod ISO 15552 profile cylinder featuring a 40mm adjustable stroke window, allowing the retract end position to be dialed in for an effective stroke range of 120-160mm. Because a rod exits both ends, the annulus area is symmetrical, delivering equal force both ways at 345 N each direction at 0.5 MPa.
This extruded aluminum barrel design omits external tie rods and includes field-adjustable air cushions at both ends to decelerate the load near the stroke extremes. This specific SKU lacks a magnet (-S), so it cannot directly host CMSE or DMSE position sensors without modification. The PT1/8 port and M10x1.25 rod thread are standard for the 32mm bore.
| Model | Airtac SEJ Adjustable Cylinder SEJ32X160-40 |
|---|---|
| Series | SEJ ISO 15552 adjustable-stroke cylinder |
| Bore size | Ø32 mm |
| Nominal stroke | 160 mm |
| Adjustment window | 40 mm (120–160 mm) |
| Configuration | Double rod, double acting |
| Port size | PT1/8 |
| Rod thread | M10×1.25 |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 27 mm |
Specifications follow the official AirTAC SEJ datasheet and ISO 15552 / VDMA 24562 dimensions. The adjustment screw shortens the retract end only; do not exceed the 40mm window. Port options: PT (standard) / G (BSPP).
| Pressure | Force (both directions) |
|---|---|
| 0.5 MPa | 346 N |
| 0.7 MPa | 484 N |
| Max (@1.0 MPa) | 70 kgf |
A rod exits both ends, so extend and retract force are identical. Actual usable force is lower than theoretical; size with a safety margin.
| SEJ | ISO 15552 double-rod double-acting cylinder with adjustable stroke. |
|---|---|
| 32 | Bore size in mm. |
| ×160 | Nominal stroke length in mm. |
| -40 | Adjustment stroke window in mm (options: 10/20/30/40/50/75/100). |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting (SEJ): Basic, LB, FA, TC, FTC, TCM1, TCM2. Related: SED (double rod, fixed stroke), SE (single rod).
Fine-tune the 120-160mm retract position on an adhesive dispenser head, using the 345 N both-way force to maintain consistent bead spacing during commissioning.
Dial the stop screw up to 40mm to accommodate different package heights on a conveyor transfer without swapping out the entire cylinder hardware.
Verify the 40mm adjustment window covers your machine's required end-position range, yielding a 120-160mm effective stroke. If you need less force, the adjacent smaller bore is unavailable in this series (32mm is the minimum), but if you need more clamping power, stepping up to the 40mm bore yields 528 N both ways at 0.5 MPa. If your end position never changes, a fixed-stroke SED is sufficient. Remember that the adjustable cushion and stop screw decelerate the load but do not hold position on air loss; for fail-safe holding, use an external rod lock. For a 160mm stroke, ensure external guides support the load to prevent side-loading on the rod. ISO 15552 dimensional interchangeability means it drops into existing setups matching the 32mm bore, 160mm stroke, PT1/8 port, and Basic/FA/LB/TC/FTC/TCM1/TCM2 mounting footprint.
Quick checklist
The cylinder has a 40mm adjustment window on the back rod, meaning the effective retract stroke can be mechanically dialed in anywhere from 120mm to 160mm. You set the exact end position and lock the stop screw in place on the machine.
Because the rod exits both ends, the force is identical in both directions: 345 N at 0.5 MPa, 483 N at 0.7 MPa, and a maximum of 70 kgf at 1.0 MPa.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Most standard models are dispatched in 3-5 days.
Most inquiries answered within 7 hours.
Send us the quantity and destination. We confirm price, availability and lead time — usually within 7 hours.