
The AirTAC SEJ Adjustable Cylinder SEJ32X280-100S is a genuine double-acting ISO 15552 double-rod cylinder with a mechanically ADJUSTABLE stroke: a back-rod stop screw lets you fine-tune the retract end over a 100mm window, so this Ø32mm unit covers an effective stroke of 180–280mm without changing cylinders. Force is equal in both directions.
The AirTAC SEJ32X280-100S is a double-acting, double-rod ISO 15552 profile cylinder with a 100 mm adjustable stroke window. A rod exits both ends, meaning the annulus area is identical in both directions and yields an equal force of 345 N each way at 0.5 MPa. You can dial the retract end-position from 180 mm up to the nominal 280 mm via a mechanical stop screw on the back rod, then lock it in place for exact machine commissioning.
Because the stroke is 280 mm on a 32 mm bore, external guides are recommended to prevent side-loading on the 12 mm rod. The extruded aluminum barrel has no external tie rods, and field-adjustable air cushions at both ends let you tune deceleration. The integrated magnet (-S) supports CMSE reed and DMSE electronic sensors for position feedback.
| Model | Airtac SEJ Adjustable Cylinder SEJ32X280-100S |
|---|---|
| Series | SEJ ISO 15552 adjustable-stroke cylinder |
| Bore size | Ø32 mm |
| Nominal stroke | 280 mm |
| Adjustment window | 100 mm (180–280 mm) |
| Configuration | Double rod, double acting |
| Port size | PT1/8 |
| Rod thread | M10×1.25 |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 27 mm |
Specifications follow the official AirTAC SEJ datasheet and ISO 15552 / VDMA 24562 dimensions. The adjustment screw shortens the retract end only; do not exceed the 100mm window. Port options: PT (standard) / G (BSPP).
| Pressure | Force (both directions) |
|---|---|
| 0.5 MPa | 346 N |
| 0.7 MPa | 484 N |
| Max (@1.0 MPa) | 70 kgf |
A rod exits both ends, so extend and retract force are identical. Actual usable force is lower than theoretical; size with a safety margin.
| SEJ | ISO 15552 double-rod double-acting cylinder with adjustable stroke. |
|---|---|
| 32 | Bore size in mm. |
| ×280 | Nominal stroke length in mm. |
| -100 | Adjustment stroke window in mm (options: 10/20/30/40/50/75/100). |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting (SEJ): Basic, LB, FA, TC, FTC, TCM1, TCM2. Related: SED (double rod, fixed stroke), SE (single rod).
Dial the 100 mm window to fine-tune the 180-280 mm retract position for varying circuit board heights. The equal 345 N both-way force securely lifts and lowers the 12 mm rod pickup head.
Adjust the mechanical stop screw on the fly when switching carton sizes. The double-rod design keeps speed and force identical extend and retract, preventing jagged carton seals.
Trial different retraction depths for a dispense valve without swapping hardware. The -S magnet works with DMSE electronic sensors to confirm the exact fluid shot height.
Verify the 100 mm adjustment window covers your required end-position range. If you need less fine-tune travel, a shorter window or a fixed-stroke SED saves cost. Stepping down is not an option below 32 mm, but stepping up to the 40 mm bore raises the both-way force to 528 N at 0.5 MPa. The 32 mm bore provides 345 N at 0.5 MPa and 483 N at 0.7 MPa.
For an ISO 15552 replacement, match the 280 mm stroke, 100 mm window, PT1/8 port, and your mounting choice from Basic, FA, LB, TC, FTC, TCM1, or TCM2. Note that the adjustable stop screw and air cushions only set the mechanical end and decelerate the load; they do not hold position on air loss. For fail-safe holding, specify an external rod lock.
Quick checklist
The back rod features a mechanical stop screw that lets you dial the retract stroke over a 100 mm window. You can set the effective stroke anywhere from 180 mm up to the nominal 280 mm, then lock the screw to secure the end-position.
Because it is a double-rod cylinder, the force is identical in both directions. It outputs 345 N at 0.5 MPa, 483 N at 0.7 MPa, and has a maximum force of 70 kgf at 1.0 MPa.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Most standard models are dispatched in 3-5 days.
Most inquiries answered within 7 hours.
Send us the quantity and destination. We confirm price, availability and lead time — usually within 7 hours.