
The AirTAC SEJ Adjustable Cylinder SEJ32X70-10S is a genuine double-acting ISO 15552 double-rod cylinder with a mechanically ADJUSTABLE stroke: a back-rod stop screw lets you fine-tune the retract end over a 10mm window, so this Ø32mm unit covers an effective stroke of 60–70mm without changing cylinders. Force is equal in both directions.
The AirTAC SEJ32X70-10S is a double-acting, double-rod ISO 15552 profile cylinder featuring a 10mm adjustable stroke window. A rod exits both ends, meaning the annulus area is identical in both directions. This provides an equal output force of 345 N each way at 0.5 MPa, ensuring perfectly balanced push and pull operations.
You can dial the retract end-position from 60 to 70 mm using a stop screw on the back rod, allowing precise machine commissioning without swapping hardware. The extruded aluminum barrel contains no external tie rods, and the included magnet supports CMSE reed and DMSE electronic sensors for position feedback.
| Model | Airtac SEJ Adjustable Cylinder SEJ32X70-10S |
|---|---|
| Series | SEJ ISO 15552 adjustable-stroke cylinder |
| Bore size | Ø32 mm |
| Nominal stroke | 70 mm |
| Adjustment window | 10 mm (60–70 mm) |
| Configuration | Double rod, double acting |
| Port size | PT1/8 |
| Rod thread | M10×1.25 |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 27 mm |
Specifications follow the official AirTAC SEJ datasheet and ISO 15552 / VDMA 24562 dimensions. The adjustment screw shortens the retract end only; do not exceed the 10mm window. Port options: PT (standard) / G (BSPP).
| Pressure | Force (both directions) |
|---|---|
| 0.5 MPa | 346 N |
| 0.7 MPa | 484 N |
| Max (@1.0 MPa) | 70 kgf |
A rod exits both ends, so extend and retract force are identical. Actual usable force is lower than theoretical; size with a safety margin.
| SEJ | ISO 15552 double-rod double-acting cylinder with adjustable stroke. |
|---|---|
| 32 | Bore size in mm. |
| ×70 | Nominal stroke length in mm. |
| -10 | Adjustment stroke window in mm (options: 10/20/30/40/50/75/100). |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting (SEJ): Basic, LB, FA, TC, FTC, TCM1, TCM2. Related: SED (double rod, fixed stroke), SE (single rod).
Fine-tune the 60 to 70 mm effective stroke during machine commissioning to set an exact dispenser nozzle gap, locking the back-rod stop screw once the ideal position is found.
Verify the 10 mm adjustment window covers your required end-position variance. If you need less force, the adjacent bore down is not available in this series, but if you need more power, stepping up to the 40 mm bore yields 528 N at 0.5 MPa. If your stroke never changes, a fixed-stroke SED cylinder is sufficient. Remember that the adjustable air cushion only decelerates the load near stroke end; it is not a mechanical lock, so an external rod lock is required for fail-safe holding.
For ISO 15552 dimensional replacements, match the 32 mm bore, 70 mm nominal stroke, PT1/8 port, and mounting choice (Basic, FA, LB, TC, FTC, TCM1, or TCM2). Because the overall length is longer than a double-rod cylinder to accommodate the rear adjustment screw, verify your axial mounting envelope.
Quick checklist
The adjustment window is 10 mm. You can mechanically dial the retract stroke from a minimum of 60 mm up to the nominal 70 mm using the back-rod stop screw, allowing precise end-position tuning on the machine.
Because the rod exits both ends, force is equal in both directions. It generates 345 N at 0.5 MPa, 483 N at 0.7 MPa, and a maximum of 70 kgf at 1.0 MPa.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Most standard models are dispatched in 3-5 days.
Most inquiries answered within 7 hours.
Send us the quantity and destination. We confirm price, availability and lead time — usually within 7 hours.