
The AirTAC SEJ Adjustable Cylinder SEJ40X310-30S is a genuine double-acting ISO 15552 double-rod cylinder with a mechanically ADJUSTABLE stroke: a back-rod stop screw lets you fine-tune the retract end over a 30mm window, so this Ø40mm unit covers an effective stroke of 280–310mm without changing cylinders. Force is equal in both directions.
The AirTAC SEJ40X310-30S is a double-acting, double-rod ISO 15552 profile cylinder. A rod exits both ends, yielding identical annulus areas so thrust is equal in both directions at 528 N each way at 0.5 MPa. An integrated magnet supports CMSE reed and DMSE electronic sensors for position tracking.
This unit features a 30 mm adjustable stroke window, letting you dial the retract end from 280 mm up to the nominal 310 mm. A mechanical stop screw on the back rod sets the exact end position, which you lock down after fine-tuning. The extruded aluminum barrel omits external tie rods, and field-adjustable air cushions at both ends decelerate the load near stroke end.
| Model | Airtac SEJ Adjustable Cylinder SEJ40X310-30S |
|---|---|
| Series | SEJ ISO 15552 adjustable-stroke cylinder |
| Bore size | Ø40 mm |
| Nominal stroke | 310 mm |
| Adjustment window | 30 mm (280–310 mm) |
| Configuration | Double rod, double acting |
| Port size | PT1/4 |
| Rod thread | M12×1.25 |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 30 mm |
Specifications follow the official AirTAC SEJ datasheet and ISO 15552 / VDMA 24562 dimensions. The adjustment screw shortens the retract end only; do not exceed the 30mm window. Port options: PT (standard) / G (BSPP).
| Pressure | Force (both directions) |
|---|---|
| 0.5 MPa | 528 N |
| 0.7 MPa | 739 N |
| Max (@1.0 MPa) | 108 kgf |
A rod exits both ends, so extend and retract force are identical. Actual usable force is lower than theoretical; size with a safety margin.
| SEJ | ISO 15552 double-rod double-acting cylinder with adjustable stroke. |
|---|---|
| 40 | Bore size in mm. |
| ×310 | Nominal stroke length in mm. |
| -30 | Adjustment stroke window in mm (options: 10/20/30/40/50/75/100). |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting (SEJ): Basic, LB, FA, TC, FTC, TCM1, TCM2. Related: SED (double rod, fixed stroke), SE (single rod).
Dial in the 30 mm retract window to match varying carton widths on the fly, using the 528 N both-way force to push and pull the diverter flap precisely.
Fine-tune the 280-310 mm effective stroke on the machine to set exact contact depth for pressing bearings without changing hardware.
Adjust the end stop quickly when switching the line to a new product height, leveraging equal push and pull forces for stable positioning.
Verify the 30 mm adjustment window covers your required end-position range. If you need less force, the adjacent 32 mm bore delivers 345 N both ways at 0.5 MPa. For heavier demands, stepping up to the 63 mm bore provides 1402 N both ways at 0.5 MPa. If your machine never requires stroke changes, a fixed-stroke SED cylinder is sufficient. For drop prevention on air loss, add an external rod lock, as the cushion and stop screw are not brakes. At 310 mm stroke, guide external rods to prevent side-load wear. Match your ISO 15552 replacement by confirming PT1/4 ports, the M12x1.25 rod thread, and your preferred mounting set (Basic, FA, LB, TC, FTC, TCM1, TCM2).
Quick checklist
A stop screw on the rear rod mechanically shortens the retract stroke over a 30 mm window. You can dial the effective stroke from 280 mm up to 310 mm, then lock the screw to hold that exact end position.
Because the rod exits both ends, force is equal in both directions: 528 N at 0.5 MPa, 739 N at 0.7 MPa, and a maximum of 108 kgf at 1.0 MPa.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Standard models are processed and dispatched in 3-5 business days.
Most inquiries answered within 7-8 hours.
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.