
The AirTAC SEJ Adjustable Cylinder SEJ40X80-10S is a genuine double-acting ISO 15552 double-rod cylinder with a mechanically ADJUSTABLE stroke: a back-rod stop screw lets you fine-tune the retract end over a 10mm window, so this Ø40mm unit covers an effective stroke of 70–80mm without changing cylinders. Force is equal in both directions.
The AirTAC SEJ40X80-10S is a double-acting, double-rod ISO 15552 profile cylinder with a 10mm adjustable stroke window, yielding an effective travel range of 70 to 80 mm. A rod extends from both ends, ensuring the annulus area remains identical in both directions for equal push and pull forces.
You dial in the retract end position via a mechanical stop screw on the back rod, locking it after setting your exact machine target. This extruded aluminum barrel design omits external tie rods, and the included -S magnet supports CMSE reed and DMSE electronic sensors for precise end-of-stroke detection.
| Model | Airtac SEJ Adjustable Cylinder SEJ40X80-10S |
|---|---|
| Series | SEJ ISO 15552 adjustable-stroke cylinder |
| Bore size | Ø40 mm |
| Nominal stroke | 80 mm |
| Adjustment window | 10 mm (70–80 mm) |
| Configuration | Double rod, double acting |
| Port size | PT1/4 |
| Rod thread | M12×1.25 |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 30 mm |
Specifications follow the official AirTAC SEJ datasheet and ISO 15552 / VDMA 24562 dimensions. The adjustment screw shortens the retract end only; do not exceed the 10mm window. Port options: PT (standard) / G (BSPP).
| Pressure | Force (both directions) |
|---|---|
| 0.5 MPa | 528 N |
| 0.7 MPa | 739 N |
| Max (@1.0 MPa) | 108 kgf |
A rod exits both ends, so extend and retract force are identical. Actual usable force is lower than theoretical; size with a safety margin.
| SEJ | ISO 15552 double-rod double-acting cylinder with adjustable stroke. |
|---|---|
| 40 | Bore size in mm. |
| ×80 | Nominal stroke length in mm. |
| -10 | Adjustment stroke window in mm (options: 10/20/30/40/50/75/100). |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting (SEJ): Basic, LB, FA, TC, FTC, TCM1, TCM2. Related: SED (double rod, fixed stroke), SE (single rod).
Dial in the 70-80 mm retract stop to match varying part heights on an electronics pick-and-place, using the 528 N both-way force to lift components securely.
Fine-tune the exact end position for pressing bearings, relying on the equal push/pull force to prevent jamming during press and withdrawal.
Quickly adjust the mechanical end stop for different packaging carton sizes without swapping out the entire cylinder hardware.
Verify the 10 mm adjustment window covers your required end-position variance; if you need a larger tuning range, step up to a 20 mm window variant. For sizing, stepping down to a 32 mm bore drops your both-way force to 345 N at 0.5 MPa, while stepping up to a 50 mm bore increases it to 825 N. If your stroke never changes after commissioning, a fixed-stroke SED is sufficient.
This cylinder does not hold position on air loss; the adjustable air cushion and mechanical stop only set the end and decelerate near stroke travel completion. For fail-safe holding, use an external rod lock. As an ISO 15552 cylinder, it dimensionally interchanges by bore, stroke, PT1/4 port, and mounting choice (Basic, FA, LB, TC, FTC, TCM1, TCM2).
Quick checklist
A stop screw on the back rod lets you mechanically shorten the retract stroke by up to 10 mm. The effective stroke range is 70 to 80 mm. You lock the screw after finding the exact end position.
Because a rod exits both ends, force is identical in both directions: 528 N at 0.5 MPa, 739 N at 0.7 MPa, and a maximum of 108 kgf at 1.0 MPa.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Standard models are processed and dispatched in 3-5 business days.
Most inquiries answered within 7-8 hours.
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.