
The AirTAC SEJ Adjustable Cylinder SEJ40X80-30S is a genuine double-acting ISO 15552 double-rod cylinder with a mechanically ADJUSTABLE stroke: a back-rod stop screw lets you fine-tune the retract end over a 30mm window, so this Ø40mm unit covers an effective stroke of 50–80mm without changing cylinders. Force is equal in both directions.
The AirTAC SEJ40X80-30S is a double-acting, double-rod ISO 15552 profile cylinder with a 30mm adjustable stroke window. A rod exits both ends, yielding identical annulus areas and an equal force of 528 N each way at 0.5 MPa. You can dial the retract end from 50mm up to the nominal 80mm.
A stop screw on the back rod mechanically sets the retract position, which you lock after fine-tuning the machine. The extruded aluminum barrel carries no external tie rods, and the -S magnet enables CMSE reed or DMSE electronic position sensing.
| Model | Airtac SEJ Adjustable Cylinder SEJ40X80-30S |
|---|---|
| Series | SEJ ISO 15552 adjustable-stroke cylinder |
| Bore size | Ø40 mm |
| Nominal stroke | 80 mm |
| Adjustment window | 30 mm (50–80 mm) |
| Configuration | Double rod, double acting |
| Port size | PT1/4 |
| Rod thread | M12×1.25 |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 30 mm |
Specifications follow the official AirTAC SEJ datasheet and ISO 15552 / VDMA 24562 dimensions. The adjustment screw shortens the retract end only; do not exceed the 30mm window. Port options: PT (standard) / G (BSPP).
| Pressure | Force (both directions) |
|---|---|
| 0.5 MPa | 528 N |
| 0.7 MPa | 739 N |
| Max (@1.0 MPa) | 108 kgf |
A rod exits both ends, so extend and retract force are identical. Actual usable force is lower than theoretical; size with a safety margin.
| SEJ | ISO 15552 double-rod double-acting cylinder with adjustable stroke. |
|---|---|
| 40 | Bore size in mm. |
| ×80 | Nominal stroke length in mm. |
| -30 | Adjustment stroke window in mm (options: 10/20/30/40/50/75/100). |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting (SEJ): Basic, LB, FA, TC, FTC, TCM1, TCM2. Related: SED (double rod, fixed stroke), SE (single rod).
Dial the 30mm retract window to hit carton heights precisely during changeover, using the 528 N both-way force to halt moving product without rebound.
Fine-tune the 50-80mm stroke on a circuit board insertion press during commissioning, locking the back-rod stop screw once the exact insertion depth is found.
Adjust the clamping position on a machining fixture for variable raw part thicknesses, relying on equal push/pull force to keep the workpiece centered.
Verify the 30mm adjustment window covers your target end-position range (50-80mm). If you need less force, the 32mm bore delivers 345 N both ways at 0.5 MPa; if you need more, step up to the 50mm bore for 825 N at 0.5 MPa. For fixed repetitive strokes without commissioning tweaks, a standard SED double-rod cylinder is sufficient.
This unit uses a PT1/4 port and an M12x1.25 rod thread. Remember that a plain SEJ does not hold position on air loss; the adjustable air cushion and stop screw only decelerate the load and set the mechanical end. For fail-safe holding, specify a BSED or an external rod lock.
Quick checklist
A stop screw on the rear rod lets you mechanically shorten the retract stroke within a 30mm window. The effective stroke range is 50-80mm, which you set and lock on the machine during commissioning.
Because the rod exits both ends, the force is identical in both directions: 528 N at 0.5 MPa, 739 N at 0.7 MPa, and a maximum of 108 kgf at 1.0 MPa.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Standard models are processed and dispatched in 3-5 business days.
Most inquiries answered within 7-8 hours.
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.