
The AirTAC SEJ Adjustable Cylinder SEJ40X80-50S is a genuine double-acting ISO 15552 double-rod cylinder with a mechanically ADJUSTABLE stroke: a back-rod stop screw lets you fine-tune the retract end over a 50mm window, so this Ø40mm unit covers an effective stroke of 30–80mm without changing cylinders. Force is equal in both directions.
The AirTAC SEJ40X80-50S is a double-acting, double-rod ISO 15552 profile cylinder featuring a mechanically adjustable retract stroke. A rod exits both ends, yielding identical annulus areas and an equal drive force of 528 N each way at 0.5 MPa (739 N at 0.7 MPa). A stop screw on the back rod lets you dial the retract end up to 50 mm, creating an effective stroke range of 30-80 mm without swapping hardware.
This extruded aluminum barrel omits external tie rods for a clean profile. The included magnet (-S) supports CMSE reed and DMSE electronic sensors for end-of-stroke confirmation. Field-adjustable air cushions at both ends decelerate the load near the stroke terminus, while the PT1/4 port and M12x1.25 rod thread simplify integration.
| Model | Airtac SEJ Adjustable Cylinder SEJ40X80-50S |
|---|---|
| Series | SEJ ISO 15552 adjustable-stroke cylinder |
| Bore size | Ø40 mm |
| Nominal stroke | 80 mm |
| Adjustment window | 50 mm (30–80 mm) |
| Configuration | Double rod, double acting |
| Port size | PT1/4 |
| Rod thread | M12×1.25 |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 30 mm |
Specifications follow the official AirTAC SEJ datasheet and ISO 15552 / VDMA 24562 dimensions. The adjustment screw shortens the retract end only; do not exceed the 50mm window. Port options: PT (standard) / G (BSPP).
| Pressure | Force (both directions) |
|---|---|
| 0.5 MPa | 528 N |
| 0.7 MPa | 739 N |
| Max (@1.0 MPa) | 108 kgf |
A rod exits both ends, so extend and retract force are identical. Actual usable force is lower than theoretical; size with a safety margin.
| SEJ | ISO 15552 double-rod double-acting cylinder with adjustable stroke. |
|---|---|
| 40 | Bore size in mm. |
| ×80 | Nominal stroke length in mm. |
| -50 | Adjustment stroke window in mm (options: 10/20/30/40/50/75/100). |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting (SEJ): Basic, LB, FA, TC, FTC, TCM1, TCM2. Related: SED (double rod, fixed stroke), SE (single rod).
Dial in the exact 30-80 mm end-position during setup, using the 528 N both-way force to precisely clamp a workpiece without overtravel.
Quickly adjust retract depth to accommodate varying product heights on a packaging line, shifting the stop screw up to 50 mm between runs.
Test actuation points on a new fixture by fine-tuning the retract stroke, leveraging equal push and pull forces for stable probing.
Verify the 50 mm adjustment window covers your positioning range; this bore provides 528 N both ways at 0.5 MPa. If you need less force, the 32 mm bore offers 345 N; if you need more, step up to the 50 mm bore for 825 N. For fixed-position tasks without end-tuning, a standard SED double-rod cylinder is sufficient. The air cushion and stop screw decelerate the load but do not hold position on air loss; use an external rod lock for fail-safe holding. Ensure your ISO 15552 replacement matches the 80 mm nominal stroke, 50 mm window, PT1/4 port, and magnet option.
Quick checklist
The stop screw on the rear rod allows you to shorten the retract stroke by up to 50 mm. This gives an effective stroke range of 30 mm to 80 mm, which you lock in place after setting.
Because the rod exits both ends, force is identical in both directions: 528 N at 0.5 MPa, 739 N at 0.7 MPa, and a maximum of 108 kgf at 1.0 MPa.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Standard models are processed and dispatched in 3-5 business days.
Most inquiries answered within 7-8 hours.
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.