
The AirTAC SEJ Adjustable Cylinder SEJ63X450-100SFA is a genuine double-acting ISO 15552 double-rod cylinder with a mechanically ADJUSTABLE stroke: a back-rod stop screw lets you fine-tune the retract end over a 100mm window, so this Ø63mm unit covers an effective stroke of 350–450mm without changing cylinders. Force is equal in both directions.
The AirTAC SEJ63X450-100SFA is a double-acting, double-rod ISO 15552 profile cylinder featuring a 100 mm mechanical stroke adjustment window. A rod exits both ends, yielding identical annulus areas so thrust is perfectly balanced at 1402 N each way at 0.5 MPa. You dial the retract end from 350 mm up to the full 450 mm nominal stroke using a stop screw on the back rod, then lock it to fix the exact machine end-position without swapping hardware.
This FA-mounted unit includes a magnet for CMSE reed or DMSE electronic position sensing. Because the stroke is 450 mm, the extended rod length increases susceptibility to side loads; ensure external guides support the tooling to prevent binding. The extruded aluminum barrel contains no external tie rods, and adjustable air cushions at both ends absorb kinetic energy near stroke termination.
| Model | Airtac SEJ Adjustable Cylinder SEJ63X450-100SFA |
|---|---|
| Series | SEJ ISO 15552 adjustable-stroke cylinder |
| Bore size | Ø63 mm |
| Nominal stroke | 450 mm |
| Adjustment window | 100 mm (350–450 mm) |
| Configuration | Double rod, double acting |
| Port size | PT3/8 |
| Rod thread | M16×1.5 |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 36 mm |
Specifications follow the official AirTAC SEJ datasheet and ISO 15552 / VDMA 24562 dimensions. The adjustment screw shortens the retract end only; do not exceed the 100mm window. Port options: PT (standard) / G (BSPP).
| Pressure | Force (both directions) |
|---|---|
| 0.5 MPa | 1402 N |
| 0.7 MPa | 1962 N |
| Max (@1.0 MPa) | 286 kgf |
A rod exits both ends, so extend and retract force are identical. Actual usable force is lower than theoretical; size with a safety margin.
| SEJ | ISO 15552 double-rod double-acting cylinder with adjustable stroke. |
|---|---|
| 63 | Bore size in mm. |
| ×450 | Nominal stroke length in mm. |
| -100 | Adjustment stroke window in mm (options: 10/20/30/40/50/75/100). |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting (SEJ): Basic, LB, FA, TC, FTC, TCM1, TCM2. Related: SED (double rod, fixed stroke), SE (single rod).
Dial the 100 mm retract window to lift pallets of varying heights. The 1402 N both-way force at 0.5 MPa securely shifts loads, while the FA mount fixes the body to your machine frame.
Fine-tune the exact 350-450 mm pressing depth on a light assembly press. The double-rod design ensures the 1962 N retract force matches the extend force, maintaining consistent pressure.
Adjust the gate stroke on the fly to accommodate different package sizes on a conveyor. The rear stop screw locks the 100 mm window precisely, and the -S magnet tracks position via DMSE sensors.
Verify the 100 mm adjustment window covers your required end-position variance, providing a 350-450 mm effective range. For sizing both ways: stepping down to a 50 mm bore yields 825 N at 0.5 MPa, while stepping up to an 80 mm bore provides 2268 N. If your application never requires position changes after commissioning, a fixed-stroke SED saves cost and length. Note that the adjustable cushion and stop screw decelerate the load but do not hold position on air loss; for fail-safe holding, specify a BSED or an external rod lock. When replacing an ISO 15552 cylinder, match the 63 mm bore, 450 mm stroke, PT3/8 port, FA mount, and -S magnet.
Quick checklist
The -100 code indicates a 100 mm adjustment window. A stop screw on the rear rod lets you mechanically set the retract stroke anywhere from 350 mm up to the 450 mm nominal stroke. You lock the screw after finding the exact end-position.
Because it is a double-rod cylinder, force is equal in both directions. It provides 1402 N at 0.5 MPa, 1962 N at 0.7 MPa, and a maximum of 286 kgf at 1.0 MPa.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Most standard models are dispatched in 3-5 days.
Most inquiries answered within 7 hours.
Send us the quantity and destination. We confirm price, availability and lead time — usually within 7 hours.