
The AirTAC SEJ Adjustable Cylinder SEJ80X260-100 is a genuine double-acting ISO 15552 double-rod cylinder with a mechanically ADJUSTABLE stroke: a back-rod stop screw lets you fine-tune the retract end over a 100mm window, so this Ø80mm unit covers an effective stroke of 160–260mm without changing cylinders. Force is equal in both directions.
The AirTAC SEJ80X260-100 is a double-acting, double-rod ISO 15552 profile cylinder featuring a 100 mm adjustable stroke window. A stop screw on the rear rod lets you dial the retract end position, yielding an effective stroke range of 160 to 260 mm. This mechanical adjustability is ideal for fine-tuning end stops directly on the machine during commissioning.
Because a rod exits both ends, the annulus area is identical in both directions, delivering an equal force of 2268 N each way at 0.5 MPa. The extruded aluminum barrel omits external tie rods, and adjustable air cushions at both ends decelerate the 25 mm rod near stroke extremes. This SKU has no magnet, so it does not support CMSE or DMSE position sensors.
| Model | Airtac SEJ Adjustable Cylinder SEJ80X260-100 |
|---|---|
| Series | SEJ ISO 15552 adjustable-stroke cylinder |
| Bore size | Ø80 mm |
| Nominal stroke | 260 mm |
| Adjustment window | 100 mm (160–260 mm) |
| Configuration | Double rod, double acting |
| Port size | PT3/8 |
| Rod thread | M20×1.5 |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 36 mm |
Specifications follow the official AirTAC SEJ datasheet and ISO 15552 / VDMA 24562 dimensions. The adjustment screw shortens the retract end only; do not exceed the 100mm window. Port options: PT (standard) / G (BSPP).
| Pressure | Force (both directions) |
|---|---|
| 0.5 MPa | 2268 N |
| 0.7 MPa | 3175 N |
| Max (@1.0 MPa) | 463 kgf |
A rod exits both ends, so extend and retract force are identical. Actual usable force is lower than theoretical; size with a safety margin.
| SEJ | ISO 15552 double-rod double-acting cylinder with adjustable stroke. |
|---|---|
| 80 | Bore size in mm. |
| ×260 | Nominal stroke length in mm. |
| -100 | Adjustment stroke window in mm (options: 10/20/30/40/50/75/100). |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting (SEJ): Basic, LB, FA, TC, FTC, TCM1, TCM2. Related: SED (double rod, fixed stroke), SE (single rod).
Adjust the stroke from 160 to 260 mm on packaging lines to divert different carton sizes without swapping hardware, relying on equal force both ways for smooth retraction.
Fine-tune the end-of-travel position of heavy 80 mm bore actuators during machine build, locking the rear stop screw precisely once the mechanical datum is set.
Verify the 100 mm adjustment window covers your positioning range. If you need less force, the 63 mm bore provides 1402 N at 0.5 MPa; if you need more, the 100 mm bore yields 3681 N at 0.5 MPa. If your end position never changes, a fixed-stroke SED avoids the adjustment mechanism. Remember that the air cushion and stop screw only set the mechanical end and decelerate the load; they do not hold position on air loss. For fail-safe holding, use an external rod lock. At 260 mm stroke, guide external loads to prevent side-loading the rod. Match ISO 15552 replacements by bore, port PT3/8, and mounting (Basic, FA, LB, TC, FTC, TCM1, TCM2).
Quick checklist
The 100 mm adjustment window allows you to mechanically shorten the retract stroke from 260 mm down to 160 mm. You set the exact end position using a stop screw on the back rod, then lock it in place.
Because the rod exits both ends, force is equal in both directions: 2268 N at 0.5 MPa, 3175 N at 0.7 MPa, and a maximum of 463 kgf at 1.0 MPa.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Most standard models are dispatched in 3-5 days.
Most inquiries answered within 7 hours.
Send us the quantity and destination. We confirm price, availability and lead time — usually within 7 hours.