
The AirTAC SEJ Adjustable Cylinder SEJ80X50-20 is a genuine double-acting ISO 15552 double-rod cylinder with a mechanically ADJUSTABLE stroke: a back-rod stop screw lets you fine-tune the retract end over a 20mm window, so this Ø80mm unit covers an effective stroke of 30–50mm without changing cylinders. Force is equal in both directions.
The AirTAC SEJ80X50-20 is a double-acting, double-rod ISO 15552 profile cylinder with a 20 mm adjustable stroke window, yielding an effective stroke range of 30 to 50 mm. A rod exits both ends, ensuring the annular area is identical in both directions. This provides an equal drive force of 2268 N each way at 0.5 MPa and 3175 N at 0.7 MPa.
You dial in the retract end position using a stop screw on the back rod, then lock it down for precise machine commissioning. The extruded aluminum barrel carries no external tie rods, and the field-adjustable air cushions at both ends decelerate the load near the stroke ends. This SKU has no magnet, so it does not support position sensors.
| Model | Airtac SEJ Adjustable Cylinder SEJ80X50-20 |
|---|---|
| Series | SEJ ISO 15552 adjustable-stroke cylinder |
| Bore size | Ø80 mm |
| Nominal stroke | 50 mm |
| Adjustment window | 20 mm (30–50 mm) |
| Configuration | Double rod, double acting |
| Port size | PT3/8 |
| Rod thread | M20×1.5 |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 36 mm |
Specifications follow the official AirTAC SEJ datasheet and ISO 15552 / VDMA 24562 dimensions. The adjustment screw shortens the retract end only; do not exceed the 20mm window. Port options: PT (standard) / G (BSPP).
| Pressure | Force (both directions) |
|---|---|
| 0.5 MPa | 2268 N |
| 0.7 MPa | 3175 N |
| Max (@1.0 MPa) | 463 kgf |
A rod exits both ends, so extend and retract force are identical. Actual usable force is lower than theoretical; size with a safety margin.
| SEJ | ISO 15552 double-rod double-acting cylinder with adjustable stroke. |
|---|---|
| 80 | Bore size in mm. |
| ×50 | Nominal stroke length in mm. |
| -20 | Adjustment stroke window in mm (options: 10/20/30/40/50/75/100). |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting (SEJ): Basic, LB, FA, TC, FTC, TCM1, TCM2. Related: SED (double rod, fixed stroke), SE (single rod).
Dial in the exact 30-50 mm retract stop for a 2268 N press fit operation, locking the back rod once the bearing seat is perfectly seated.
Shift the retract end up to 20 mm to accommodate varying part heights on a machining fixture without swapping out the entire 3175 N cylinder.
Fine-tune the clamping reach during machine commissioning, using the 80 mm bore's equal both-way force to securely grip castings.
Confirm the 20 mm adjustment window covers your required end-position variance within the 30-50 mm effective range. If you need less force, the adjacent 63 mm bore delivers 1402 N at 0.5 MPa; if you need more, stepping up to the 100 mm bore yields 3681 N each way at 0.5 MPa. If your end position never changes, a fixed-stroke SED cylinder is sufficient. Remember that the adjustable cushion and stop screw only set the mechanical end and decelerate the load; a plain SEJ does not hold position on air loss, so use an external rod lock for fail-safe holding. When replacing an ISO 15552 cylinder, match the 80 mm bore, 50 mm stroke, PT3/8 port, and mounting choice from the Basic, FA, LB, TC, FTC, TCM1, or TCM2 set.
Quick checklist
A stop screw on the back rod lets you mechanically shorten the retract stroke by up to 20 mm. This gives an effective stroke range of 30 to 50 mm, which you set and lock during commissioning. It only adjusts the mechanical end position and does not hold the load on air loss.
Because a rod exits both ends, the force is identical in both directions. It provides 2268 N at 0.5 MPa, 3175 N at 0.7 MPa, and a maximum of 463 kgf at 1.0 MPa.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Most standard models are dispatched in 3-5 days.
Most inquiries answered within 7 hours.
Send us the quantity and destination. We confirm price, availability and lead time — usually within 7 hours.