
The AirTAC SEJ Adjustable Cylinder SEJ80X50-30 is a genuine double-acting ISO 15552 double-rod cylinder with a mechanically ADJUSTABLE stroke: a back-rod stop screw lets you fine-tune the retract end over a 30mm window, so this Ø80mm unit covers an effective stroke of 20–50mm without changing cylinders. Force is equal in both directions.
The AirTAC SEJ80X50-30 is a double-acting, double-rod ISO 15552 profile cylinder with a 30 mm adjustable stroke window, yielding an effective travel range of 20-50 mm. A rod exits both ends, meaning the annulus area is identical in both directions. This provides equal force and speed extending and retracting, delivering 2268 N each way at 0.5 MPa.
You dial in the exact retract end-position using a mechanical stop screw on the back rod, then lock it in place. This cylinder features an extruded aluminum barrel with no external tie rods, adjustable air cushions at both ends, and a PT3/8 port. This SKU omits the magnet, so it does not support CMSE or DMSE position sensors.
| Model | Airtac SEJ Adjustable Cylinder SEJ80X50-30 |
|---|---|
| Series | SEJ ISO 15552 adjustable-stroke cylinder |
| Bore size | Ø80 mm |
| Nominal stroke | 50 mm |
| Adjustment window | 30 mm (20–50 mm) |
| Configuration | Double rod, double acting |
| Port size | PT3/8 |
| Rod thread | M20×1.5 |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 36 mm |
Specifications follow the official AirTAC SEJ datasheet and ISO 15552 / VDMA 24562 dimensions. The adjustment screw shortens the retract end only; do not exceed the 30mm window. Port options: PT (standard) / G (BSPP).
| Pressure | Force (both directions) |
|---|---|
| 0.5 MPa | 2268 N |
| 0.7 MPa | 3175 N |
| Max (@1.0 MPa) | 463 kgf |
A rod exits both ends, so extend and retract force are identical. Actual usable force is lower than theoretical; size with a safety margin.
| SEJ | ISO 15552 double-rod double-acting cylinder with adjustable stroke. |
|---|---|
| 80 | Bore size in mm. |
| ×50 | Nominal stroke length in mm. |
| -30 | Adjustment stroke window in mm (options: 10/20/30/40/50/75/100). |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting (SEJ): Basic, LB, FA, TC, FTC, TCM1, TCM2. Related: SED (double rod, fixed stroke), SE (single rod).
Dial the 30 mm retract window to match varying die heights during production changeovers, using the 2268 N both-way force to consistently lift and lower stamping tools.
Fine-tune the diverting distance on a packaging line without swapping hardware, adjusting the stroke from 20 to 50 mm to route different carton sizes accurately.
Commission a clamping press by setting the exact mechanical end stop for delicate parts, leveraging the equal 3175 N extend and retract forces at 0.7 MPa.
Verify the 30 mm adjustment window covers your required end-position range. If you need less force, the 63 mm bore provides 1402 N at 0.5 MPa; if you need more, stepping up to the 100 mm bore yields 3681 N both ways. If you never need to alter the stroke after commissioning, a fixed-stroke SED double-rod cylinder is sufficient.
This cylinder provides 3175 N at 0.7 MPa and 463 kgf at 1.0 MPa. Note that the adjustable cushion and stop screw decelerate the load near stroke end but do not hold position on air loss; for fail-safe holding, use an external rod lock. Dimensionally interchangeable per ISO 15552, match the 80 mm bore, 50 mm stroke, PT3/8 port, and mounting choice (Basic, FA, LB, TC, FTC, TCM1, or TCM2) for a direct replacement.
Quick checklist
The 30 mm adjustment window allows you to mechanically dial the retract stroke from 50 mm down to 20 mm. You set the exact end-position via a stop screw on the back rod and lock it, which is ideal for fine-tuning during machine commissioning.
Because the rod exits both ends, force is identical in both directions: 2268 N at 0.5 MPa, 3175 N at 0.7 MPa, and a maximum of 463 kgf at 1.0 MPa.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Most standard models are dispatched in 3-5 days.
Most inquiries answered within 7 hours.
Send us the quantity and destination. We confirm price, availability and lead time — usually within 7 hours.