
The AirTAC SEJ Adjustable Cylinder SEJ80X70-40S is a genuine double-acting ISO 15552 double-rod cylinder with a mechanically ADJUSTABLE stroke: a back-rod stop screw lets you fine-tune the retract end over a 40mm window, so this Ø80mm unit covers an effective stroke of 30–70mm without changing cylinders. Force is equal in both directions.
The AirTAC SEJ80X70-40S is a double-acting, double-rod ISO 15552 profile cylinder. A rod exits both ends, ensuring identical annulus areas for equal force and speed in both directions. The retract stroke is mechanically adjustable via a stop screw on the back rod over a 40 mm window, yielding an effective stroke range of 30-70 mm.
This unit includes a magnet for position sensing and uses an extruded aluminum barrel without external tie rods. It features field-adjustable air cushions at both ends to decelerate the load near stroke end.
| Model | Airtac SEJ Adjustable Cylinder SEJ80X70-40S |
|---|---|
| Series | SEJ ISO 15552 adjustable-stroke cylinder |
| Bore size | Ø80 mm |
| Nominal stroke | 70 mm |
| Adjustment window | 40 mm (30–70 mm) |
| Configuration | Double rod, double acting |
| Port size | PT3/8 |
| Rod thread | M20×1.5 |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 36 mm |
Specifications follow the official AirTAC SEJ datasheet and ISO 15552 / VDMA 24562 dimensions. The adjustment screw shortens the retract end only; do not exceed the 40mm window. Port options: PT (standard) / G (BSPP).
| Pressure | Force (both directions) |
|---|---|
| 0.5 MPa | 2268 N |
| 0.7 MPa | 3175 N |
| Max (@1.0 MPa) | 463 kgf |
A rod exits both ends, so extend and retract force are identical. Actual usable force is lower than theoretical; size with a safety margin.
| SEJ | ISO 15552 double-rod double-acting cylinder with adjustable stroke. |
|---|---|
| 80 | Bore size in mm. |
| ×70 | Nominal stroke length in mm. |
| -40 | Adjustment stroke window in mm (options: 10/20/30/40/50/75/100). |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting (SEJ): Basic, LB, FA, TC, FTC, TCM1, TCM2. Related: SED (double rod, fixed stroke), SE (single rod).
Dial the 40 mm window to fine-tune the exact 30-70 mm pressing depth on aluminum housings, utilizing the equal 3175 N both-way force at 0.7 MPa for consistent retraction.
Adjust the retract end-stop on the fly when switching between component heights on an assembly line, avoiding hardware swaps while leveraging the 463 kgf max output.
Set precise mechanical limits for trial positioning in automated test fixtures, using the back-rod stop screw to lock the exact end position after commissioning.
Verify the 40 mm adjustment window covers your required end-position range. If you need less force, the 63 mm bore provides 1402 N at 0.5 MPa; if you need more, stepping up to the 100 mm bore yields 3681 N at 0.5 MPa. If your machine never requires stroke changes, a fixed-stroke SED saves space and cost.
This cylinder does not hold position on air loss; the cushion and stop screw only set the mechanical end and decelerate the load. For fail-safe holding, specify an external rod lock. As an ISO 15552 cylinder, it mounts via Basic, FA, LB, TC, FTC, TCM1, or TCM2 brackets (omitting FB/CA/CB/CR). The -S magnet pairs with CMSE reed and DMSE electronic sensors.
Quick checklist
A stop screw on the rear rod mechanically shortens the retract stroke over a 40 mm window. For this 70 mm nominal stroke model, the effective retract range is 30-70 mm. You dial the end position and lock the screw in place.
Because it is a double-rod cylinder, the force is identical in both directions. It provides 2268 N at 0.5 MPa, 3175 N at 0.7 MPa, and a maximum of 463 kgf at 1.0 MPa.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Most standard models are dispatched in 3-5 days.
Most inquiries answered within 7 hours.
Send us the quantity and destination. We confirm price, availability and lead time — usually within 7 hours.