
The AirTAC SEJ Adjustable Cylinder SEJ80X75-10S is a genuine double-acting ISO 15552 double-rod cylinder with a mechanically ADJUSTABLE stroke: a back-rod stop screw lets you fine-tune the retract end over a 10mm window, so this Ø80mm unit covers an effective stroke of 65–75mm without changing cylinders. Force is equal in both directions.
The AirTAC SEJ80X75-10S is a double-acting, double-rod ISO 15552 profile cylinder featuring a 10mm adjustable stroke window, allowing you to dial the retract end position precisely from 65 to 75mm. Because a rod exits both ends, the annulus area is identical in both directions, yielding equal force at 2268 N each way at 0.5 MPa. This symmetry eliminates differential speeds during extend and retract cycles.
A stop screw on the back rod mechanically sets the end position, which you lock after fine-tuning the machine. The extruded aluminum barrel design omits external tie rods, and the field-adjustable air cushion at both ends decelerates the load near stroke end. Equipped with a magnet (-S), it integrates directly with CMSE reed and DMSE electronic sensors for precise position feedback.
| Model | Airtac SEJ Adjustable Cylinder SEJ80X75-10S |
|---|---|
| Series | SEJ ISO 15552 adjustable-stroke cylinder |
| Bore size | Ø80 mm |
| Nominal stroke | 75 mm |
| Adjustment window | 10 mm (65–75 mm) |
| Configuration | Double rod, double acting |
| Port size | PT3/8 |
| Rod thread | M20×1.5 |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 36 mm |
Specifications follow the official AirTAC SEJ datasheet and ISO 15552 / VDMA 24562 dimensions. The adjustment screw shortens the retract end only; do not exceed the 10mm window. Port options: PT (standard) / G (BSPP).
| Pressure | Force (both directions) |
|---|---|
| 0.5 MPa | 2268 N |
| 0.7 MPa | 3175 N |
| Max (@1.0 MPa) | 463 kgf |
A rod exits both ends, so extend and retract force are identical. Actual usable force is lower than theoretical; size with a safety margin.
| SEJ | ISO 15552 double-rod double-acting cylinder with adjustable stroke. |
|---|---|
| 80 | Bore size in mm. |
| ×75 | Nominal stroke length in mm. |
| -10 | Adjustment stroke window in mm (options: 10/20/30/40/50/75/100). |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting (SEJ): Basic, LB, FA, TC, FTC, TCM1, TCM2. Related: SED (double rod, fixed stroke), SE (single rod).
Dial in the exact 65-75mm retract stop during press die changeovers, using the equal 2268N both-way force to seat and release heavy forming tools without differential drift.
Fine-tune the actuation end-point on the fly to match varying carton sizes on a sorting line, locking the stop screw once the physical gate position is set.
Confirm this 10mm adjustment window covers your required end-position tolerance, letting you match variable stops or part heights without swapping hardware. If you need less force, stepping down to the 63mm bore yields 1402 N at 0.5 MPa, while stepping up to the 100mm bore provides 3681 N at 0.5 MPa. If your process never requires stroke adjustments, a fixed-stroke SED cylinder is a simpler alternative.
When replacing an ISO 15552 cylinder, match the 80mm bore, 75mm nominal stroke, PT3/8 port, and your required mounting bracket from the SEJ subset (Basic, FA, LB, TC, FTC, TCM1, TCM2). Note that the air cushion decelerates the load but does not hold position on air loss; for fail-safe holding, specify an external rod lock or BSED series.
Quick checklist
The retract end can be dialed in over a 10mm window, giving an effective stroke range of 65 to 75mm. You set the mechanical stop via a screw on the back rod and lock it in place once the exact machine position is reached.
Because the rod exits both ends, the output force is identical in both directions: 2268 N at 0.5 MPa, 3175 N at 0.7 MPa, and a maximum of 463 kgf at 1.0 MPa.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Most standard models are dispatched in 3-5 days.
Most inquiries answered within 7 hours.
Send us the quantity and destination. We confirm price, availability and lead time — usually within 7 hours.