
The AirTAC SEJ Adjustable Cylinder SEJ80X80-20 is a genuine double-acting ISO 15552 double-rod cylinder with a mechanically ADJUSTABLE stroke: a back-rod stop screw lets you fine-tune the retract end over a 20mm window, so this Ø80mm unit covers an effective stroke of 60–80mm without changing cylinders. Force is equal in both directions.
The AirTAC SEJ80X80-20 is a double-acting, double-rod ISO 15552 profile cylinder with a 20mm adjustable stroke window, letting you dial the retract end from 60mm up to 80mm. Because a rod exits both ends, the annulus area is identical in both directions, delivering an equal force of 2268 N each way at 0.5 MPa. The extruded aluminum barrel contains no external tie rods, ensuring clean ISO 15552 dimensional interchangeability.
You set the exact retract position via a stop screw on the back rod, then lock it down to match a mechanical stop precisely. This SKU has no magnet (-S), so it carries no position sensor, but it includes field-adjustable air cushions at both ends to decelerate the load near stroke end.
| Model | Airtac SEJ Adjustable Cylinder SEJ80X80-20 |
|---|---|
| Series | SEJ ISO 15552 adjustable-stroke cylinder |
| Bore size | Ø80 mm |
| Nominal stroke | 80 mm |
| Adjustment window | 20 mm (60–80 mm) |
| Configuration | Double rod, double acting |
| Port size | PT3/8 |
| Rod thread | M20×1.5 |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 36 mm |
Specifications follow the official AirTAC SEJ datasheet and ISO 15552 / VDMA 24562 dimensions. The adjustment screw shortens the retract end only; do not exceed the 20mm window. Port options: PT (standard) / G (BSPP).
| Pressure | Force (both directions) |
|---|---|
| 0.5 MPa | 2268 N |
| 0.7 MPa | 3175 N |
| Max (@1.0 MPa) | 463 kgf |
A rod exits both ends, so extend and retract force are identical. Actual usable force is lower than theoretical; size with a safety margin.
| SEJ | ISO 15552 double-rod double-acting cylinder with adjustable stroke. |
|---|---|
| 80 | Bore size in mm. |
| ×80 | Nominal stroke length in mm. |
| -20 | Adjustment stroke window in mm (options: 10/20/30/40/50/75/100). |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting (SEJ): Basic, LB, FA, TC, FTC, TCM1, TCM2. Related: SED (double rod, fixed stroke), SE (single rod).
Dial the 20mm retract window to hit exact sheet metal bend stops. The 2268N both-way force holds the gauge firmly against vibration during rapid 30-800 mm/s positioning.
Adjust the effective stroke from 60 to 80mm to switch carton heights without swapping hardware. The double-rod design keeps speed and force perfectly balanced during changeover.
Fine-tune the pressing position during commissioning. Lock the back-rod stop screw once the ideal 60-80mm travel is found for precise part insertion.
Confirm the 20mm adjustment window covers your required end-position range; here, effective stroke spans 60 to 80mm. For sizing both ways, the adjacent bore down (63mm) yields 1402 N at 0.5 MPa, while the next bore up (100mm) yields 3681 N at 0.5 MPa. If you do not need to fine-tune the end position on the machine, a fixed-stroke SED provides the same equal-force double-rod action. To replace an ISO 15552 cylinder, match the 80mm bore, 80mm stroke, PT3/8 port, and mounting choice (Basic, FA, LB, TC, FTC, TCM1, or TCM2). Note that the adjustable cushion and stop screw decelerate the load but do not hold position on air loss; for fail-safe holding, specify a BSED or an external rod lock.
Quick checklist
A stop screw on the rear protruding rod lets you mechanically shorten the retract stroke. For this model, you can adjust the effective stroke anywhere from 60mm up to the nominal 80mm. Once set, you lock the screw to hold the exact end position.
Because the rod exits both ends, the force is identical in both directions: 2268 N at 0.5 MPa, 3175 N at 0.7 MPa, and a maximum of 463 kgf at 1.0 MPa. The speed range is 30-800 mm/s.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Most standard models are dispatched in 3-5 days.
Most inquiries answered within 7 hours.
Send us the quantity and destination. We confirm price, availability and lead time — usually within 7 hours.