
The AirTAC SEJ Adjustable Cylinder SEJ80X830-30 is a genuine double-acting ISO 15552 double-rod cylinder with a mechanically ADJUSTABLE stroke: a back-rod stop screw lets you fine-tune the retract end over a 30mm window, so this Ø80mm unit covers an effective stroke of 800–830mm without changing cylinders. Force is equal in both directions.
The AirTAC SEJ80X830-30 is a double-acting, double-rod ISO 15552 profile cylinder featuring an adjustable stroke mechanism. A stop screw on the back rod lets you dial the retract end position over a 30mm window, providing an effective stroke range of 800 to 830mm. This eliminates the need to swap hardware when fine-tuning a long-stroke machine cycle. Because a rod exits both ends, the annular area is identical in both directions. The cylinder delivers an equal output force of 2268 N each way at 0.5 MPa and 3175 N at 0.7 MPa. The extruded aluminum barrel is dimensionally interchangeable per ISO 15552 with no external tie rods, and field-adjustable air cushions at both ends decelerate the mass near stroke extremes.
This configuration uses an 80mm bore with a PT3/8 port and a Ø25mm rod. The SKU ships without a magnet, meaning it has no CMSE or DMSE position sensor capability out of the box. The rear rod can carry a flag or cam for external sequencing, and the overall length is longer than a fixed-stroke SED model due to the integrated adjustment hardware.
| Model | Airtac SEJ Adjustable Cylinder SEJ80X830-30 |
|---|---|
| Series | SEJ ISO 15552 adjustable-stroke cylinder |
| Bore size | Ø80 mm |
| Nominal stroke | 830 mm |
| Adjustment window | 30 mm (800–830 mm) |
| Configuration | Double rod, double acting |
| Port size | PT3/8 |
| Rod thread | M20×1.5 |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 36 mm |
Specifications follow the official AirTAC SEJ datasheet and ISO 15552 / VDMA 24562 dimensions. The adjustment screw shortens the retract end only; do not exceed the 30mm window. Port options: PT (standard) / G (BSPP).
| Pressure | Force (both directions) |
|---|---|
| 0.5 MPa | 2268 N |
| 0.7 MPa | 3175 N |
| Max (@1.0 MPa) | 463 kgf |
A rod exits both ends, so extend and retract force are identical. Actual usable force is lower than theoretical; size with a safety margin.
| SEJ | ISO 15552 double-rod double-acting cylinder with adjustable stroke. |
|---|---|
| 80 | Bore size in mm. |
| ×830 | Nominal stroke length in mm. |
| -30 | Adjustment stroke window in mm (options: 10/20/30/40/50/75/100). |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting (SEJ): Basic, LB, FA, TC, FTC, TCM1, TCM2. Related: SED (double rod, fixed stroke), SE (single rod).
Dial in the exact 800-830mm retract position to feed sheet stock into a press, using the 3175 N both-way force to push heavy carriers without stroke reconfiguration.
Adjust the stop position on the fly during line changeovers to accommodate different pallet lengths, leveraging the equal push and pull forces to halt and release loads securely.
Fine-tune the end-of-stroke contact point during equipment commissioning to test large assemblies, relying on the 30mm window to find the precise engagement distance.
Verify the 30mm adjustment window covers your commissioning range, yielding an effective 800-830mm stroke. For sizing both ways: stepping down to the 63mm bore drops the both-way force to 1402 N at 0.5 MPa, while stepping up to the 100mm bore increases it to 3681 N at 0.5 MPa. If your end position never varies after commissioning, a fixed-stroke SED cylinder is enough. If you need fail-safe position holding on air loss, note that the adjustable stop screw and air cushions only set the mechanical end and decelerate motion; they do not lock the rod. You must pair this cylinder with an external rod lock or BSED for fail-safe hold. At 830mm of stroke, ensure external guides support side loads to prevent rod binding. When matching an ISO 15552 replacement, confirm the 80mm bore, 830mm nominal stroke, 30mm window, PT3/8 port, and mounting choice (Basic, FA, LB, TC, FTC, TCM1, or TCM2).
Quick checklist
A stop screw on the rear rod mechanically shortens the retract stroke. You can dial the end position over a 30mm window, giving an effective stroke range of 800 to 830mm. Lock the screw after setting your exact position.
Because the rod exits both ends, force is equal in both directions. It provides 2268 N at 0.5 MPa, 3175 N at 0.7 MPa, and a maximum of 463 kgf at 1.0 MPa.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Most standard models are dispatched in 3-5 days.
Most inquiries answered within 7 hours.
Send us the quantity and destination. We confirm price, availability and lead time — usually within 7 hours.