
The AirTAC SGCJ200-250 Adjustable Cylinder SGCJ250X50-10 is a genuine double acting, double rod, adjustable stroke ISO 15552 (orig. ISO 6431) tie-rod air cylinder with a Ø250mm bore and 50mm stroke, G1 air ports and adjustable end cushioning. Its large-bore tie-rod build delivers high thrust and drops into standardized ISO 15552 mounting on heavy automation.
Generating massive thrust for heavy industrial tasks, this large-bore ISO 15552 tie-rod cylinder pushes with 24543 N and pulls with 23562 N at 0.5 MPa. The four steel tie rods clamp the aluminum barrel securely to the covers, while the G1 air port feeds the 50 mm piston rod. Because this is a 250 mm bore unit, the TPU seal option is not available; instead it uses NBR buffer gaskets, with a Viton H high-temperature upgrade possible for 0 to 150 C environments.
The -10 code defines an external adjuster that shortens the extend stroke on site by up to 10 mm, letting you fine-tune the end position without changing the cylinder itself. The nominal 50 mm stroke remains the maximum, yielding a usable extend range of 40 to 50 mm. This plain SKU lacks a magnet, so it cannot take CMSG, DMSG or EMSG sensors without specifying the -S variant.
| Model | Airtac SGCJ200-250 Adjustable Cylinder SGCJ250X50-10 |
|---|---|
| Series | SGC ISO 15552 tie-rod cylinder |
| Bore size | Ø250 mm |
| Stroke | 50 mm |
| Acting type | Double acting, double rod, adjustable stroke |
| Port size | G1 |
| Rod thread | M42×2.0 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 500 mm/s |
| Cushion | Adjustable, 60 mm |
| Max standard stroke | Up to 1500 mm |
Specifications follow the official AirTAC SGC datasheet and ISO 15552 dimensions. Confirm against the product label before installation. Thread options: PT (blank) / G. TPU seals are not available for the Ø250 bore (NBR / Viton only).
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 23562 N | 23562 N |
| 0.7 MPa | 32987 N | 32987 N |
| Max (@1.0 MPa) | 4805 kgf | |
SGCJ is double-rod: the rear rod that carries the stroke adjuster passes through the rear cover, so both piston faces lose rod area. Push is shown at the annular-area value (conservative).
| SGCJ | ISO 15552 tie-rod cylinder (adjustable-stroke type). |
|---|---|
| 250 | Bore size in mm (125 / 160 / 200 / 250). |
| ×50 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSG / DMSG / EMSG sensors. |
SGC-family variants: SGC (double acting), SGCD (double rod), SGCJ (adjustable stroke). Mounting: LB / FA / FB / CA / CB / CR / TC / FTC / TCM1 / TCM2. Seals: TPU (blank) / Viton H / NBR N. On Ø250 the blank code is the standard NBR build (no TPU).
Dial in the exact bottoming point of a heavy stamping press within a 40 to 50 mm window using the external adjuster, avoiding mechanical spacer changes.
Lower a 1200 kg platen smoothly using the 60 mm adjustable air cushions at both ends, tweaking the extend stop to hit the target drop height precisely.
Act as a robust stop block on a heavy-duty conveyor, fine-tuning the 10 mm extend window to accommodate different pallet depths without swapping hardware.
When sizing this unit, stepping down to a 200 mm bore drops the 0.5 MPa push force to 15708 N, while this 250 mm bore hits 24543 N and represents the top standard capacity. The 10 mm adjustable window is ideal when you need to share a spare cylinder across slightly different stroke variants or dial in a precise end position on the machinery. Mounting options include FA, LB, TC, FTC, TCM1 and TCM2 brackets. Note that a plain cylinder drifts without live air, so fit an external rod lock or pilot-operated check valve if you must hold a suspended load. Even at this short 50 mm stroke, ensure adequate guidance to absorb side loads.
Quick checklist
At 0.5 MPa it pushes with 24543 N and pulls with 23562 N. At 0.7 MPa the push is 34360 N and the pull is 32986 N. The theoretical maximum force is 5006 kgf at 1.0 MPa. This 250 mm bore unit uses a G1 air port, a 50 mm rod, an M42x2.0 rod thread and 60 mm adjustable cushions.
The -10 indicates an external adjuster that lets you shorten the extend stroke by up to 10 mm on site. The nominal 50 mm stroke is the maximum, so the usable extend range is 40 to 50 mm. The retract end remains fixed. This mechanism only sets the end position and does not lock the load; you still need an external rod lock or pilot-operated check valve to hold a load without live air.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Large-bore cylinders built to order — confirm lead time.
Most inquiries answered within 7-8 hours.
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.