Airtac SGCJ200-250 Adjustable Cylinder SGCJ250X80-100
The AirTAC Airtac SGCJ200-250 Adjustable Cylinder SGCJ250X80-100 is a genuine double acting, adjustable stroke ISO 15552 (orig. ISO 6431) tie-rod air cylinder with a Ø250mm bore and 80mm stroke, G1 air ports and adjustable end cushioning. Its large-bore tie-rod build delivers high thrust and drops into standardized ISO 15552 mounting on heavy automation.
- BoreØ250 mm
- Stroke80 mm
- Port sizeG1
- Acting typeDouble acting, adjustable stroke
- Rod threadM42×2.0
- CushionAdjustable, 60 mm
About the Airtac SGCJ200-250 Adjustable Cylinder SGCJ250X80-100
Delivering 24543 N of push force at 0.5 MPa, this large-bore ISO 15552 tie-rod cylinder integrates a 100 mm external adjuster to fine-tune the extend end position on site. Four steel tie rods clamp the aluminum barrel to the covers, providing structural rigidity, while the ISO 15552 mounting interface ensures dimensional interchangeability for large-bore fixtures. The G1 air port and 50 mm piston rod handle heavy loads, and the 60 mm adjustable air cushions decelerate the piston at both ends.
Because the nominal 80 mm stroke represents the maximum extend length, the external stop screw lets you shorten the travel by up to 100 mm without changing the cylinder itself. This translates to a safe working load of roughly 14726 N, or about 1251 kg lifted vertically with a 2:1 margin. Note that this SKU lacks a magnet and cannot take a sensor; adding the -S variant enables CMSG/DMSG/EMSG switches. Also, TPU seals are not available on this 250 mm bore, though a Viton H option extends the operating temperature range from 0 to 150 C.
Airtac SGCJ200-250 Adjustable Cylinder SGCJ250X80-100 Technical Specifications
| Model | Airtac SGCJ200-250 Adjustable Cylinder SGCJ250X80-100 |
|---|---|
| Series | SGC ISO 15552 tie-rod cylinder |
| Bore size | Ø250 mm |
| Stroke | 80 mm |
| Acting type | Double acting, adjustable stroke |
| Port size | G1 |
| Rod thread | M42×2.0 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 500 mm/s |
| Cushion | Adjustable, 60 mm |
| Max standard stroke | Up to 1500 mm |
Specifications follow the official AirTAC SGC datasheet and ISO 15552 dimensions. Confirm against the product label before installation. Thread options: PT (blank) / G. TPU seals are not available for the Ø250 bore (NBR / Viton only).
Theoretical Output Force (Ø250mm)
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 24544 N | 23562 N |
| 0.7 MPa | 34361 N | — |
| Max (@1.0 MPa) | 5006 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
Model Code: Airtac SGCJ200-250 Adjustable Cylinder SGCJ250X80-100
| SGCJ | ISO 15552 tie-rod cylinder (adjustable-stroke type). |
|---|---|
| 250 | Bore size in mm (125 / 160 / 200 / 250). |
| ×80 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSG / DMSG / EMSG sensors. |
SGC-family variants: SGC (double acting), SGCD (double rod), SGCJ (adjustable stroke). Mounting: LB / FA / FB / CA / CB / CR / TC / FTC / TCM1 / TCM2. Seals: TPU (blank) / Viton H / NBR N.
Where the Airtac SGCJ200-250 Adjustable Cylinder SGCJ250X80-100 Is Used
Heavy Pallet Clamping
Provides 1251 kg of vertical holding margin to secure heavy pallets during banding, with the 100 mm adjuster tuning the clamp reach for varying load sizes.
Hydraulic Press Tonnage
Generates 24543 N of thrust at 0.5 MPa for light pressing operations, allowing operators to dial in the exact 0 to 80 mm extend depth via the external stop screw.
Large Mold Ejection
Ejects substantial industrial molds using a 50 mm rod and G1 port, with 60 mm adjustable cushions decelerating the heavy payload at stroke end.
Is the Airtac SGCJ200-250 Adjustable Cylinder SGCJ250X80-100 the Right Cylinder?
When sizing this unit, the 250 mm bore sits at the top edge of the SGCJ range, delivering 24543 N push at 0.5 MPa compared to 15708 N on the neighbouring 200 mm bore. The 100 mm adjustable window is ideal for sharing a single spare across multiple stroke variants or dialing in exact end positions on-site. Mounting options include Basic, FA, LB, TC, FTC, TCM1, and TCM2 brackets. Because this is a non-magnet SKU, it cannot accept position sensors; you must specify the -S option to use CMSG, DMSG, or EMSG switches. Even at an 80 mm stroke, always verify your guide bearings to prevent side-load wear.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Stroke and mounting space
- ✓ Port/thread type (PT / G / NPT)
- ✓ Magnet (-S) for sensors?
- ✓ Long-stroke side load — support the rod end
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Avoid side load; support long strokes at the rod end.
- check Set cushions to minimum, then release gradually.
- check Use correct mounting accessory (LB/FA/FB/CA/CB/CR/TC).
- check Installation by qualified personnel per AirTAC docs.
Airtac SGCJ200-250 Adjustable Cylinder SGCJ250X80-100 FAQ
This 250 mm bore cylinder uses a G1 port, a 50 mm piston rod with an M42x2.0 thread, and 60 mm adjustable air cushions. It delivers 24543 N push and 23562 N pull at 0.5 MPa, 34360 N push and 32986 N pull at 0.7 MPa, with a theoretical maximum of 5006 kgf at 1.0 MPa.
The nominal 80 mm stroke is the maximum extend length. The external adjuster lets you shorten the extend stroke by up to 100 mm on site to fine-tune the end position, while the retract end remains fixed. This stop only sets position; it does not hold the load on air loss, so you need an external rod lock or pilot-operated check valve for load holding.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Made to Order
Large-bore cylinders built to order — confirm lead time.
Fast Reply
Most inquiries answered within 7-8 hours.
Related AirTAC SGC Cylinders
Request a Quote for Airtac SGCJ200-250 Adjustable Cylinder SGCJ250X80-100
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.