Airtac TACED Guided Compact Cylinder TACED50X10S
The AirTAC TACED Guided Compact Cylinder TACED50X10S is a genuine double acting, double rod, non-rotating ISO 21287 compact air cylinder with a Ø50mm bore and 10mm stroke, 1/8" air ports and a hard-anodized aluminium body. Its short compact envelope saves about 50% of the mounting length of an ISO 15552 profile cylinder. Twin guide rods keep the tooling from rotating.
- BoreØ50 mm
- Stroke10 mm
- Port size1/8"
- Acting typeDouble acting, double rod, non-rotating
- Rod threadM10×1.5
- CushionFixed TPU bumper (both ends)
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac TACED Guided Compact Cylinder TACED50X10S
A double acting, double-rod compact cylinder built to ISO 21287, the TACED50X10S pushes a 16 mm rod out of BOTH covers, so the 50 mm bore delivers an identical 881.2 N in each direction at 0.5 MPa (1233.7 N at 0.7 MPa). Twin guide rods on the yoke stop the tooling rotating and carry side load, keeping a gripper or press plate square without any external guide. The hard-anodized aluminium body pairs with an S45C hard-chrome plated rod for long service life.
The short ISO 21287 body saves about 50% of the mounting length of an ISO 15552 profile cylinder, which is why this model slots into tight fixture plates and shallow machine frames. A fixed TPU bumper at each end absorbs end-of-stroke energy, and the fitted -S magnet accepts CMSE / DMSE switches for end-position sensing.
Airtac TACED Guided Compact Cylinder TACED50X10S Technical Specifications
| Model | Airtac TACED Guided Compact Cylinder TACED50X10S |
|---|---|
| Series | TACED compact cylinder |
| Standard | ISO 21287 |
| Bore size | Ø50 mm |
| Stroke | 10 mm |
| Acting type | Double acting, double rod, non-rotating |
| Port size | 1/8" |
| Rod thread | M10×1.5 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 500 mm/s |
| Cushion | Fixed TPU bumper (both ends) |
| Max standard stroke | Up to 100 mm |
Specifications follow the official AirTAC ACE-series (ISO 21287) datasheet. Body: hard-anodized aluminium alloy; piston rod: S45C carbon steel with hard-chrome plating; guide rods: stainless steel (Ø12-40) / S45C (larger). Rod type: female thread (blank) or male thread (B). Thread options: PT (blank) / G. A built-in magnet is OPTIONAL — add the -S code to fit CMSE / DMSE position sensors.
Theoretical Output Force (Ø50mm)
| Pressure | Force (both ways) |
|---|---|
| 0.5 MPa | 881 N |
| 0.7 MPa | 1234 N |
| Max (@1.0 MPa) | 180 kgf |
Double-rod: a rod exits both covers, so output force is equal in both directions (rod-side area used). Twin guide rods carry the side load and stop the tooling rotating.
Model Code: Airtac TACED Guided Compact Cylinder TACED50X10S
| TACED | ISO 21287 compact cylinder (double-rod non-rotating (twin-guide yoke)). |
|---|---|
| 50 | Bore size in mm. |
| ×10 | Stroke length in mm. |
| S | Optional built-in magnet for CMSE / DMSE sensors (omit for no magnet). |
ACE-family variants: ACE (double acting), ASE / ATE (single acting push / pull), ACED (double rod), ACEJ (double rod, adjustable stroke), TACE / TACED (non-rotating twin-guide yoke). Mounting accessories: FA / FB flange, LB foot, CA / CB clevis, CR, SDB pivot, FTC; plus I and Y knuckles. Thread PT (blank) / G.
Where the Airtac TACED Guided Compact Cylinder TACED50X10S Is Used
Short-stroke stamping mark
The 10 mm throw and 881.2 N both ways let a punch mark serial codes on aluminium housings without the cylinder overhanging the fixture.
Square gripper actuation
Twin guide rods keep a pick-and-place gripper from rotating when handling glass panels, so no separate guide rail is needed on the robot end effector.
Presence confirm station
With the -S magnet and a DMSE switch, an assembly line verifies a connector is fully seated in a shallow jig where a full-length cylinder cannot fit.
Is the Airtac TACED Guided Compact Cylinder TACED50X10S the Right Cylinder?
At 881.2 N per direction, the 50 mm bore sits between the 40 mm (571.8 N) and 63 mm (1458.1 N) options - step down when the load is light, step up for heavier clamping. The 10 mm stroke suits short-throw jobs like part presence or ejection. Remember the piston drifts if air is lost, so add a rod lock or pilot check valve where a load must stay held. This version carries the optional -S magnet for CMSE / DMSE switching, uses a female M10x1.5 rod thread with a 1/8" PT port, and mounts via FB flange, CA/CB/CR clevis or FTC foot.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Short stroke fits the compact body
- ✓ Port/thread type (PT / G)
- ✓ Add -S if you need the magnet for sensors
- ✓ Rod type (female / male B) & mount (FA/LB/CA)
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Compact body: keep the stroke short and avoid side load on the rod.
- check Do not dismantle the threaded front/back covers.
- check Keep speed within the rated range; the TPU bumper absorbs stroke-end energy.
- check Installation by qualified personnel per AirTAC docs.
Airtac TACED Guided Compact Cylinder TACED50X10S FAQ
Because a rod exits both covers, force is equal in both directions: 881.2 N at 0.5 MPa and 1233.7 N at 0.7 MPa, with a maximum of 179.7 kgf at 1.0 MPa.
The ISO 21287 short body saves about 50% of the mounting length of an ISO 15552 profile cylinder, and fixed TPU bumpers at both ends absorb end-of-stroke energy. This model carries the optional -S magnet, so CMSE / DMSE reed or solid-state switches can be clamped to the body slots for position feedback.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Request a Quote for Airtac TACED Guided Compact Cylinder TACED50X10S
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.