Airtac TACED Guided Compact Cylinder TACED50X90S
The AirTAC TACED Guided Compact Cylinder TACED50X90S is a genuine double acting, double rod, non-rotating ISO 21287 compact air cylinder with a Ø50mm bore and 90mm stroke, 1/8" air ports and a hard-anodized aluminium body. Its short compact envelope saves about 50% of the mounting length of an ISO 15552 profile cylinder. Twin guide rods keep the tooling from rotating.
- BoreØ50 mm
- Stroke90 mm
- Port size1/8"
- Acting typeDouble acting, double rod, non-rotating
- Rod threadM10×1.5
- CushionFixed TPU bumper (both ends)
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac TACED Guided Compact Cylinder TACED50X90S
A double acting, double-rod compact cylinder built to ISO 21287, the TACED50X90S pushes a 16 mm rod out of both covers, so the 50 mm bore delivers 881.2 N at 0.5 MPa and 1233.7 N at 0.7 MPa in either direction - the rod-side area is identical on both strokes. Twin guide rods on the yoke stop the tooling rotating and carry side load, keeping a gripper or press plate square without an external guide.
The hard-anodized aluminium body with an S45C hard-chrome plated rod runs at 0.15-1.0 MPa (22-145 psi) and 30-500 mm/s, with a fixed TPU bumper at each end. Because the short ISO 21287 body saves about 50% of the mounting length of an ISO 15552 profile cylinder, it slots into tight fixtures and gantries. The fitted -S magnet lets CMSE / DMSE switches report position.
Airtac TACED Guided Compact Cylinder TACED50X90S Technical Specifications
| Model | Airtac TACED Guided Compact Cylinder TACED50X90S |
|---|---|
| Series | TACED compact cylinder |
| Standard | ISO 21287 |
| Bore size | Ø50 mm |
| Stroke | 90 mm |
| Acting type | Double acting, double rod, non-rotating |
| Port size | 1/8" |
| Rod thread | M10×1.5 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 500 mm/s |
| Cushion | Fixed TPU bumper (both ends) |
| Max standard stroke | Up to 100 mm |
Specifications follow the official AirTAC ACE-series (ISO 21287) datasheet. Body: hard-anodized aluminium alloy; piston rod: S45C carbon steel with hard-chrome plating; guide rods: stainless steel (Ø12-40) / S45C (larger). Rod type: female thread (blank) or male thread (B). Thread options: PT (blank) / G. A built-in magnet is OPTIONAL — add the -S code to fit CMSE / DMSE position sensors.
Theoretical Output Force (Ø50mm)
| Pressure | Force (both ways) |
|---|---|
| 0.5 MPa | 881 N |
| 0.7 MPa | 1234 N |
| Max (@1.0 MPa) | 180 kgf |
Double-rod: a rod exits both covers, so output force is equal in both directions (rod-side area used). Twin guide rods carry the side load and stop the tooling rotating.
Model Code: Airtac TACED Guided Compact Cylinder TACED50X90S
| TACED | ISO 21287 compact cylinder (double-rod non-rotating (twin-guide yoke)). |
|---|---|
| 50 | Bore size in mm. |
| ×90 | Stroke length in mm. |
| S | Optional built-in magnet for CMSE / DMSE sensors (omit for no magnet). |
ACE-family variants: ACE (double acting), ASE / ATE (single acting push / pull), ACED (double rod), ACEJ (double rod, adjustable stroke), TACE / TACED (non-rotating twin-guide yoke). Mounting accessories: FA / FB flange, LB foot, CA / CB clevis, CR, SDB pivot, FTC; plus I and Y knuckles. Thread PT (blank) / G.
Where the Airtac TACED Guided Compact Cylinder TACED50X90S Is Used
Symmetric press or riveting station
Equal 881.2 N force on approach and return lets one TACED50X90S form or stake small brackets on both strokes, with the twin guide yoke keeping the punch square over the 90 mm travel.
Dual-side gripper on a robot cell
A rod exiting both covers drives two gripper jaws at once with matched force, so the cell picks stamped housings from either side without a second cylinder or external guide.
Reciprocating transfer on a packaging line
The through-rod pushes a product tray forward and pulls it back at the same 881.2 N rating, while the fitted -S magnet and DMSE switch confirm each end position at 30-500 mm/s.
Is the Airtac TACED Guided Compact Cylinder TACED50X90S the Right Cylinder?
At 881.2 N per side at 0.5 MPa, the 50 mm bore sits mid-range: step down to a TACED32 (345.6 N) for lighter pick-and-place, or up to a TACED63 (1458.1 N) for heavier clamping. Remember the piston drifts if air is lost - add a rod lock or pilot check valve where a load must be held. The 90 mm stroke is well inside the 250 mm standard limit for this bore, the 1/8" port takes PT fittings, and the fitted -S magnet pairs with CMSE / DMSE switches; FB flange mounting is available.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Short stroke fits the compact body
- ✓ Port/thread type (PT / G)
- ✓ Add -S if you need the magnet for sensors
- ✓ Rod type (female / male B) & mount (FA/LB/CA)
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Compact body: keep the stroke short and avoid side load on the rod.
- check Do not dismantle the threaded front/back covers.
- check Keep speed within the rated range; the TPU bumper absorbs stroke-end energy.
- check Installation by qualified personnel per AirTAC docs.
Airtac TACED Guided Compact Cylinder TACED50X90S FAQ
Yes - the double-rod design exposes the rod-side area on both strokes, so output is equal either way: 881.2 N at 0.5 MPa, 1233.7 N at 0.7 MPa, with a maximum of 179.7 kgf at 1.0 MPa. Operating pressure is 0.15-1.0 MPa (22-145 psi), proof pressure 1.5 MPa (215 psi), and speed 30-500 mm/s.
It is an ISO 21287 compact cylinder whose short hard-anodized aluminium body saves about 50% of the mounting length of an ISO 15552 profile cylinder, with a fixed TPU bumper at each end to absorb end-of-stroke energy. This model carries the optional -S magnet, so CMSE or DMSE reed and solid-state switches can be clamped into the body slots; FB flange mounting is offered, and the female rod thread is M10x1.5.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Request a Quote for Airtac TACED Guided Compact Cylinder TACED50X90S
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.