verified AirTAC China Authorized Export Seller shield 100% Genuine AirTAC Parts workspace_premium 1-Year Warranty
appsShop by Modelexpand_more
person shopping_cart Request a QuoteQuote
AirTAC TWG40 · Adjustable mounting height Stopper Cylinder

Airtac TWG Stop Cylinder TWG40X30SB

Genuine AirTAC adjustable mounting height stopper cylinder, order code TWG40X30SB from the TWG40 range. The options this code selects are decoded below; series data follow the official AirTAC catalog.

  • Stroke30 mm
  • StopperFlat rod
  • MagnetMagnet
  • ActionDouble acting
  • MountingFlange, adjustable mounting height
  • BoreØ40 mm
$65.10 $72.60Save 10%
Request a Quote
  • No minimum order. A single piece can be ordered.
  • Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
Compare every TWG40 stroke, stopper and magnet on one page All TWG40 codes →
verified Genuine AirTAC workspace_premium 1-year warranty bolt Reply in 7-8 h

About the Airtac TWG Stop Cylinder TWG40X30SB

The AirTAC TWG40X30SB is a double acting Dia 40 mm stopper cylinder with a 30 mm stroke (tolerance +1.0/0 mm) and the B flat rod stopper, whose wider face spreads the impact of a stopped pallet or box over a broader contact area than a round rod. The S in the order code confirms the built-in magnet, so reed or Hall-effect position sensors can signal whether the stopper is raised or lowered at the machine.

The flange mounts with an adjustable mounting height, letting you set the stop point on the conveyor frame. Switching air through the PT1/8 port at 0.15-1.0 MPa raises and lowers the stopper, the bumper cushion absorbs the return, and the series runs from -20 to +70 C with no lubrication required.

Airtac TWG Stop Cylinder TWG40X30SB Technical Specifications

Order codeTWG40X30SB
ProductAdjustable mounting height Stopper Cylinder
Stroke30 mm
StopperFlat rod
MagnetMagnet
ActionDouble acting
MountingFlange, adjustable mounting height
BoreØ40 mm
Strokes20, 25, 30 mm (+1.0/0)
PortPT1/8
Stopper typesRound rod, Flat rod, Roller, Lever roller, adjustable oil cushion
FluidAir (filtered by 40 µm element)
Operating pressure0.15-1.0 MPa
Proof pressure1.5 MPa (215 psi)
Temperature-20 to +70 °C
CushionBumper
LubricationNot required

Source: AirTAC Products Catalog 2026A (PDF01-P0756..P0757), TWG series specifications and ordering code.

How to choose

Choose TWG40X30SB when a wide flat contact face and sensor feedback are both wanted on the same 30 mm stopper. The TWG40X30B equivalent without S gives the same flat rod but no magnet, while TWG40X30SC swaps the flat face for a round rod and TWG40X30R uses a roller that loads can ride over. Self-lock is only available on the lever roller K code.

Applications

warehouse

Carton stop stations

The flat rod face spreads the contact across cartons in picking and sorting zones, and the magnet signals stopper position to the control system.

packaging

Pallet accumulation

Use the Dia 40 flat rod stopper to hold pallets at packing stations, with the magnet feeding raised and lowered states into the line controller.

sensors

Automated stopper feedback

The S magnet option makes this code fit monitored conveyor stops where a sensor must confirm whether the load is being held or released.

FAQ

What are the key figures of the AirTAC TWG40X30SB?

Dia 40 mm bore, 30 mm stroke (+1.0/0 mm tolerance), double acting, flat rod stopper, magnet included, flange with adjustable mounting height, PT1/8 port, operating pressure 0.15-1.0 MPa, proof pressure 1.5 MPa (215 psi), temperature -20 to +70 C, bumper cushion, no lubrication required.

What does the S in TWG40X30SB do?

Per the ordering code table, S adds a magnet so position sensors can detect the stopper state; blank leaves the cylinder without a magnet. The B selects the flat rod stopper, and the F self-lock option does not apply to this stopper type.