Airtac TWG Stop Cylinder TWG40X30SC
Genuine AirTAC adjustable mounting height stopper cylinder, order code TWG40X30SC from the TWG40 range. The options this code selects are decoded below; series data follow the official AirTAC catalog.
- Stroke30 mm
- StopperRound rod
- MagnetMagnet
- ActionDouble acting
- MountingFlange, adjustable mounting height
- BoreØ40 mm
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac TWG Stop Cylinder TWG40X30SC
The AirTAC TWG40X30SC pairs the C round rod stopper with a Dia 40 mm bore, 30 mm stroke (tolerance +1.0/0 mm) and the S magnet in one double acting TWG series stopper. The round rod gives a simple, narrow contact point for stopping pallets, boxes and workpieces on conveyor lines, and the magnet lets position sensors report whether the stopper is up or down.
Mounting is a flange with adjustable mounting height, so the stop point can be set on the machine frame at assembly. The thicker piston rod of the Dia 40 body resists impact, air is switched through the PT1/8 port at 0.15-1.0 MPa, and the series runs dry from -20 to +70 C without lubrication.
Airtac TWG Stop Cylinder TWG40X30SC Technical Specifications
| Order code | TWG40X30SC |
|---|---|
| Product | Adjustable mounting height Stopper Cylinder |
| Stroke | 30 mm |
| Stopper | Round rod |
| Magnet | Magnet |
| Action | Double acting |
|---|---|
| Mounting | Flange, adjustable mounting height |
| Bore | Ø40 mm |
| Strokes | 20, 25, 30 mm (+1.0/0) |
| Port | PT1/8 |
| Stopper types | Round rod, Flat rod, Roller, Lever roller, adjustable oil cushion |
| Fluid | Air (filtered by 40 µm element) |
| Operating pressure | 0.15-1.0 MPa |
| Proof pressure | 1.5 MPa (215 psi) |
| Temperature | -20 to +70 °C |
| Cushion | Bumper |
| Lubrication | Not required |
Source: AirTAC Products Catalog 2026A (PDF01-P0756..P0757), TWG series specifications and ordering code.
How to choose
TWG40X30SC is the magnet-equipped round rod choice of the 30 mm Dia 40 family. Use TWG40X30C without the S if no sensor signal is needed, TWG40X30SB for a flat rod face, TWG40X30SR for a roller stopper with magnet, or the lever roller K code when a softer, cushioned stop matters. The F self-lock applies only to lever roller stoppers.
Applications
Point-contact pallet stops
The round rod presents a defined stop point for pallets on conveyor runs, with the magnet confirming stopper position to the controller.
Workpiece holding on assembly lines
Use the adjustable mounting height flange to set the Dia 40 round rod at the right height for stopping workpieces feeding assembly stations.
Monitored release points
With the S magnet built in, this code suits gated conveyor sections where a sensor must verify each raise and lower cycle before the next load moves.
FAQ
What are the key figures of the AirTAC TWG40X30SC?
Dia 40 mm bore, 30 mm stroke (+1.0/0 mm tolerance), double acting, round rod stopper, magnet included, flange with adjustable mounting height, PT1/8 port, operating pressure 0.15-1.0 MPa, proof pressure 1.5 MPa (215 psi), temperature -20 to +70 C, bumper cushion, no lubrication required.
How does TWG40X30SC differ from the other TWG40 stopper codes?
The C selects the round rod stopper and S adds the magnet. The same bore and stroke with a flat rod is TWG40X30SB, with a roller TWG40X30R, and the lever roller K code is the only stopper that accepts the F self-lock and adjustable oil cushion options.