verified AirTAC China Authorized Export Seller shield 100% Genuine AirTAC Parts workspace_premium 1-Year Warranty
appsShop by Modelexpand_more
person shopping_cart Request a QuoteQuote
AirTAC TWG50 · Adjustable mounting height Stopper Cylinder

Airtac TWG Stop Cylinder TWG50X20-B

Genuine AirTAC adjustable mounting height stopper cylinder, order code TWG50X20-B from the TWG50 range. The options this code selects are decoded below; series data follow the official AirTAC catalog.

  • Stroke20 mm
  • StopperFlat rod
  • MagnetNo magnet
  • ActionDouble acting
  • MountingFlange, adjustable mounting height
  • BoreØ50 mm
$65.36 $72.86Save 10%
Request a Quote
  • No minimum order. A single piece can be ordered.
  • Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
Compare every TWG50 stroke, stopper and magnet on one page All TWG50 codes →
verified Genuine AirTAC workspace_premium 1-year warranty bolt Reply in 7-8 h

About the Airtac TWG Stop Cylinder TWG50X20-B

This AirTAC stopper cylinder uses the shortest stroke in the TWG50 series, 20 mm with a +1.0/0 mm tolerance, so the flat rod lifts just far enough to catch a pallet or carton without kicking it upward. The double acting Dia 50 bore raises and lowers the rod on air, and the thick piston rod is built to take repeated impact from moving loads.

The B stopper presents a wide flat face to the workpiece, which suits square loads that would rock on a point contact. The flange mounting has an adjustable height, so you set the stop level to the conveyor frame before locking it down. It runs on filtered air (40 um element) at 0.15-1.0 MPa, follows JIS practice and needs no lubrication.

Airtac TWG Stop Cylinder TWG50X20-B Technical Specifications

Order codeTWG50X20-B
ProductAdjustable mounting height Stopper Cylinder
Stroke20 mm
StopperFlat rod
MagnetNo magnet
ActionDouble acting
MountingFlange, adjustable mounting height
BoreØ50 mm
Strokes20, 25, 30 mm (+1.0/0)
PortPT1/8
Stopper typesRound rod, Flat rod, Roller, Lever roller, adjustable oil cushion
FluidAir (filtered by 40 µm element)
Operating pressure0.15-1.0 MPa
Proof pressure1.5 MPa (215 psi)
Temperature-20 to +70 °C
CushionBumper
LubricationNot required

Source: AirTAC Products Catalog 2026A (PDF01-P0756..P0757), TWG series specifications and ordering code.

How to choose

Against the round rod TWG50X20-C, the flat rod spreads the stop force over a wider face. The TWG50X20-R roller lets the load roll on, and the TWG50X20-K lever roller adds an adjustable oil cushion plus the F self-lock that stops spring-back pushing the load backwards. For end-position sensing, order the S magnet variant instead, because this code carries no magnet.

Applications

conveyor_belt

Pallet stop at a conveyor edge

The 20 mm lift is short enough to sit below a passing pallet, then rise so the flat rod face stops it squarely on the line.

warehouse

Accumulation stop for cartons

Cartons banking on a lane lean against the wide flat face, and the Dia 50 bore with its thick rod absorbs repeated pushes without backing off.

height

Height-set fixture stop

Flange mounting with adjustable height lets the rod be set flush to the machine deck, so parts pass over it or stop on it as the cycle demands.

FAQ

What are the key figures of the TWG50X20-B?

Dia 50 mm bore, 20 mm stroke (+1.0/0 tolerance), double acting, flat rod stopper, PT1/8 port, 0.15-1.0 MPa operating pressure, 1.5 MPa (215 psi) proof pressure, -20 to +70 C, bumper cushion, no magnet.

Can I add position sensing to this cylinder later?

No. This order code has no magnet in the piston, so reed or hall switches will not detect position. If sensing is needed, specify the S magnet variant of the same bore, stroke and stopper instead, and confirm the matching switch type from the datasheet.