verified AirTAC China Authorized Export Seller shield 100% Genuine AirTAC Parts workspace_premium 1-Year Warranty
appsShop by Modelexpand_more
person shopping_cart Request a QuoteQuote
AirTAC TWG50 · Adjustable mounting height Stopper Cylinder

Airtac TWG Stop Cylinder TWG50X20SB

Genuine AirTAC adjustable mounting height stopper cylinder, order code TWG50X20SB from the TWG50 range. The options this code selects are decoded below; series data follow the official AirTAC catalog.

  • Stroke20 mm
  • StopperFlat rod
  • MagnetMagnet
  • ActionDouble acting
  • MountingFlange, adjustable mounting height
  • BoreØ50 mm
$69.29 $76.79Save 9%
Request a Quote
  • No minimum order. A single piece can be ordered.
  • Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
Compare every TWG50 stroke, stopper and magnet on one page All TWG50 codes →
verified Genuine AirTAC workspace_premium 1-year warranty bolt Reply in 7-8 h

About the Airtac TWG Stop Cylinder TWG50X20SB

The AirTAC TWG50X20SB combines a flat rod stopper with the S magnet option on a 50 mm bore, 20 mm stroke (+1.0/0 mm) double acting TWG cylinder. The flat stop face presents a wider, flat edge to the load than the round rod version, and the flange mounting height is adjustable so the stop can be set exactly where the pallet or carton edge meets it. Because the magnet is built in, reed or similar position sensors mounted on the body can confirm when the stopper is up or down.

The cylinder operates on filtered air (40 um element) at 0.15-1.0 MPa through a PT1/8 port, withstands 1.5 MPa (215 psi) proof pressure, and runs from -20 to +70 C. Cushioning is by bumper, lubrication is not required, and the series follows JIS standards. The sensor signal lets a PLC interlock the next conveyor section only after the stop is confirmed raised or lowered.

Airtac TWG Stop Cylinder TWG50X20SB Technical Specifications

Order codeTWG50X20SB
ProductAdjustable mounting height Stopper Cylinder
Stroke20 mm
StopperFlat rod
MagnetMagnet
ActionDouble acting
MountingFlange, adjustable mounting height
BoreØ50 mm
Strokes20, 25, 30 mm (+1.0/0)
PortPT1/8
Stopper typesRound rod, Flat rod, Roller, Lever roller, adjustable oil cushion
FluidAir (filtered by 40 µm element)
Operating pressure0.15-1.0 MPa
Proof pressure1.5 MPa (215 psi)
Temperature-20 to +70 °C
CushionBumper
LubricationNot required

Source: AirTAC Products Catalog 2026A (PDF01-P0756..P0757), TWG series specifications and ordering code.

How to choose

Choose TWG50X20SB when the application needs both a broad flat stop face and electrical position feedback. If a round rod end with the same sensing is preferred, use TWG50X20SC; without sensing, TWG50X20R (roller) or a non-S round rod version is the lighter choice. For a softer, cushioned stop the lever roller TWG50X20K with its adjustable oil shock absorber is the alternative, and the F self-lock (TWG50X20KF only) prevents the lever from pushing the stopped load backwards. Longer strokes are covered by TWG50X25SB and TWG50X30SB.

Applications

sensors

PLC-verified pallet stops

The built-in magnet lets position sensors report stopper state back to the controller, so the transfer only starts once the 20 mm stop is confirmed in position.

packaging

Carton accumulation on box conveyors

The flat rod face spreads the contact across the carton edge, and the adjustable flange height aligns the stop with different box sizes.

warehouse

Order picking release points

Double acting air control at 0.15-1.0 MPa raises and lowers the stop between picks, with bumper cushioning absorbing the impact of each arriving tote.

FAQ

What figures define the TWG50X20SB?

Double acting, 50 mm bore, 20 mm stroke (+1.0/0 mm), flat rod stopper, S magnet fitted for position sensors, adjustable-height flange, PT1/8 port, 0.15-1.0 MPa operating pressure, 1.5 MPa (215 psi) proof, -20 to +70 C, bumper cushion, no lubrication required.

Which sensor fits the magnet in this cylinder?

The ordering code lists S as magnet for position sensors; the specific switch series and mounting hardware should be confirmed from the datasheet before wiring the station.