
Genuine AirTAC fixed mounting height stopper cylinder, order code TWQ32X10R from the TWQ32 range. The options this code selects are decoded below; series data follow the official AirTAC catalog.
The TWQ32X10R pairs the Dia 32 mm bore of AirTAC's TWQ stopper series with the roller rod end, decoded from the ordering letter R in TWQ32X10R. It is double acting on a 10 mm stroke with a PT1/8 port, running on filtered air at 0.15-1.0 MPa. Mounting is fixed height through holes, with tapped holes at both ends as an alternative, so the stopper face sits at a set height above the conveyor rail.
Because the rod end is a roller, the contact face rolls with the moving load instead of dragging across it, which suits parts that keep sliding after the stopper rises. This code leaves the magnet blank: the body still carries sensor grooves on two sides, but without the S magnet option no switch can read piston position. The bumper cushion, 1.5 MPa (215 psi) proof pressure and JIS-aligned design come from the same TWQ32 catalog data, with no lubrication needed.
| Order code | TWQ32X10R |
|---|---|
| Product | Fixed mounting height Stopper Cylinder |
| Stroke | 10 mm |
| Stopper | Roller |
| Magnet | No magnet |
| Action | Double acting |
|---|---|
| Mounting | Through holes, tapped both ends |
| Bore | Ø32 mm |
| Strokes | 10, 15, 20 mm (+1.0/0) |
| Port | PT1/8 |
| Stopper types | Round rod, Flat rod, Roller, Lever roller, adjustable oil cushion |
| Fluid | Air (filtered by 40 µm element) |
| Operating pressure | 0.15-1.0 MPa |
| Proof pressure | 1.5 MPa (215 psi) |
| Temperature | -20 to +70 °C |
| Cushion | Bumper |
| Lubrication | Not required |
Source: AirTAC Products Catalog 2026A (PDF01-P0760..P0761), TWQ series specifications and ordering code.
Within the stopper letters, TWQ32X10B gives a flat rod face, TWQ32X10C a plain round rod, and TWQ32X10K a lever roller with an adjustable oil shock absorber for a softer, self-lockable stop (F is only offered on the K lever). Choose this R code when you want rolling contact and do not need detection; add S to the same roller build (TWQ32X10SR) when a sensor must confirm the stopper is up. Strokes on the Dia 32 bore are 10, 15 and 20 mm with a +1.0/0 tolerance, so the 10 mm build keeps lift height shortest.
Roller face stops moving totes and boxes while they continue to creep, so the contact rolls rather than abrades the load bottom.
Through-hole or tapped-both-ends mounting holds a Dia 32 stopper at conveyor height, raising 10 mm to block pallet flow on 0.15-1.0 MPa plant air.
The PT1/8 port and bumper cushion let the roller pop up between cartons on a packaging line where no piston position signal is required.
Dia 32 mm bore, 10 mm stroke (+1.0/0), roller stopper, no magnet, double acting, PT1/8 port, 0.15-1.0 MPa operating pressure, 1.5 MPa (215 psi) proof pressure, bumper cushion, -20 to +70 C, air filtered by a 40 um element, no lubrication required, through-holes or tapped-both-ends mounting.
Not with this build. TWQ32X10R has no magnet, so switches mounted in the body's two-sided sensor grooves will not read piston position. If detection is needed, order the same roller stopper with the S magnet option, coded TWQ32X10SR, and confirm switch models from the datasheet.