verified AirTAC China Authorized Export Seller shield 100% Genuine AirTAC Parts workspace_premium 1-Year Warranty
appsShop by Modelexpand_more
person shopping_cart Request a QuoteQuote
AirTAC TWQ32 · Fixed mounting height Stopper Cylinder

Airtac TWQ Stopper Cylinder TWQ32X20SR

Genuine AirTAC fixed mounting height stopper cylinder, order code TWQ32X20SR from the TWQ32 range. The options this code selects are decoded below; series data follow the official AirTAC catalog.

  • Stroke20 mm
  • StopperRoller
  • MagnetMagnet
  • ActionDouble acting
  • MountingThrough holes, tapped both ends
  • BoreØ32 mm
$65.10 $72.60Save 10%
Request a Quote
  • No minimum order. A single piece can be ordered.
  • Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
Compare every TWQ32 stroke, stopper and magnet on one page All TWQ32 codes →
verified Genuine AirTAC workspace_premium 1-year warranty bolt Reply in 7-8 h

About the Airtac TWQ Stopper Cylinder TWQ32X20SR

The TWQ32X20SR is the roller-head stopper cylinder of the AirTAC TWQ32 series: the R stopper replaces the fixed rod with a roller, so loads rolling or sliding along the conveyor meet a turning surface instead of a bare rod end. Behind it is the standard Dia 32 mm double acting body with a 20 mm stroke (+1.0/0 mm), bumper cushion and PT1/8 port, raised and lowered by air on both sides. The S magnet in this code lets position switches read the stopper's state from the sensor grooves on both sides of the body.

Note what this code does not carry: unlike the K lever roller versions there is no adjustable oil shock absorber and no F self-lock, so the roller takes the impact directly - check the catalog impact load and speed charts when sizing the bore. The cylinder runs on air filtered by a 40 um element at 0.15-1.0 MPa, handles 1.5 MPa (215 psi) proof pressure and -20 to +70 C, follows JIS standards, needs no lubrication, and mounts through holes or the tapped holes at both ends.

Airtac TWQ Stopper Cylinder TWQ32X20SR Technical Specifications

Order codeTWQ32X20SR
ProductFixed mounting height Stopper Cylinder
Stroke20 mm
StopperRoller
MagnetMagnet
ActionDouble acting
MountingThrough holes, tapped both ends
BoreØ32 mm
Strokes10, 15, 20 mm (+1.0/0)
PortPT1/8
Stopper typesRound rod, Flat rod, Roller, Lever roller, adjustable oil cushion
FluidAir (filtered by 40 µm element)
Operating pressure0.15-1.0 MPa
Proof pressure1.5 MPa (215 psi)
Temperature-20 to +70 °C
CushionBumper
LubricationNot required

Source: AirTAC Products Catalog 2026A (PDF01-P0760..P0761), TWQ series specifications and ordering code.

How to choose

In the TWQ32 stopper table, R is the roller option, sitting between the simple C round rod and B flat rod heads and the K lever roller with adjustable oil cushion. Pick this SR code when the load arrives with sideways motion or slides along the stopper face and a roller is enough to pass smoothly, but the extra damping of the K head is not required - for heavy or fast impacts step up to TWQ32X20SK, and for anti-spring-back locking to TWQ32X20SKF. It shares the 20 mm stroke with the 10 mm and 15 mm variants.

Applications

conveyor_belt

Mid-line pallet stop station

The roller head lets a moving pallet's edge ride onto a turning surface, and the S magnet signals the up/down state to switches seated in the body's side grooves.

view_module

Chain or roller transfer bay

With the stopper lowered into its 20 mm stroke, loads can pass over or through the station; raised, the roller presents a smooth face to loads arriving sideways along the conveyor.

speed

High-cycle go/no-go gating

The plain roller head with bumper cushion and no oil shock absorber is the simpler TWQ32 choice for repeated short stops where impact energy stays within the catalog load chart limits.

FAQ

What are the key figures of the TWQ32X20SR?

Dia 32 mm bore, 20 mm stroke (+1.0/0 mm), double acting, PT1/8 port, 0.15-1.0 MPa operating pressure, 1.5 MPa (215 psi) proof pressure, -20 to +70 C, bumper cushion, R roller stopper, S magnet, mounting by through holes or tapped both ends, air filtered by a 40 um element, no lubrication required, JIS standards.

How does the R roller head differ from the K lever roller codes?

The R stopper is a roller alone, so the impact of the arriving load is taken directly by the roller and bumper cushion. The K codes (TWQ32X20SK and TWQ32X20SKF) use a lever roller carried on an adjustable oil shock absorber, and the SKF variant adds the F self-lock. Choose TWQ32X20SR when smooth load approach matters but impact damping and locking are not required - confirm allowable impact from the catalog charts.