This model is discontinued
AirTAC has phased out the ACP series. You can still order this code here: we ship the current replacement ACE100X175, the same code under the new prefix. The ACE replacement is a current-production ISO 21287 compact cylinder in the same bore, stroke and force class, with a matching short body and the same mounting-accessory family, so it fits the same envelope. Confirm mounting-interface dimensions against the ACE datasheet before ordering.

The AirTAC ACP Compact Cylinder ACP100X175 is a double acting DIN-standard tight/compact air cylinder with a Ø100mm bore and 175mm stroke, 1/4" air ports and a hard-anodized aluminium body. This model is discontinued — the current-production replacement is the ACE100X175 (ISO 21287 ACE), in the same bore, stroke and force class.
The ACP100X175 is a double acting compact cylinder in AirTAC's DIN-standard ACP series, with a 100 mm bore and 175 mm stroke driving a 25 mm hard-chromed S45C rod. At 0.5 MPa it pushes with 3927 N and pulls with 3681.6 N, rising to 5497.8 N at 0.7 MPa. Its short ISO 21287-class body saves roughly 50% of the mounting length of an ISO 15552 profile cylinder, so it slots into heavy press fixtures and gantries where a full-length body will not fit. Note this model is discontinued: the current-production direct is ACE100X175.
Air supply runs 0.15-1.0 MPa (22-145 psi) with 1.5 MPa (215 psi) proof pressure, speed spans 30-500 mm/s, and fixed TPU bumpers sit at both ends. The hard-anodized aluminium body takes 1/4" ports, and the rod ends in a female M16x1.5 thread. No magnet is fitted; order the -S code if you need CMSE or DMSE switch sensing.
| Model | Airtac ACP Compact Cylinder ACP100X175 |
|---|---|
| Series | ACP DIN compact cylinder (discontinued) |
| Replacement | ACE100X175 |
| Bore size | Ø100 mm |
| Stroke | 175 mm |
| Acting type | Double acting |
| Port size | 1/4" |
| Rod thread | M16×1.5 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 500 mm/s |
| Cushion | Fixed bumper (both ends) |
| Max standard stroke | Up to 300 mm |
Specifications follow the official AirTAC ACP datasheet (now discontinued). The ACE100X175 (ISO 21287) carries the same bore/stroke/force class; confirm mounting-interface dimensions against the ACE datasheet before installation. Rod type: female thread (blank) or male thread (B). Thread options: PT (blank) / G.
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 3927 N | 3682 N |
| 0.7 MPa | 5498 N | 5154 N |
| Max (@1.0 MPa) | 801 kgf | |
The ACE100X175 produces the same force from the same bore. Actual usable force is lower than theoretical; size with a margin.
| ACP | DIN compact cylinder (double-acting, discontinued). |
|---|---|
| 100 | Bore size in mm. |
| ×175 | Stroke length in mm. |
| S | Optional built-in magnet for sensor position sensing (omit for no magnet). |
| B | Rod type: B = male thread; blank = female thread. |
Replacement mapping (swap P for E): ACP→ACE, ASP→ASE, ATP→ATE, ACPD→ACED, ACPJ→ACEJ. ACP-family: ACP (double acting), ASP / ATP (single acting push / pull), ACPD (double rod), ACPJ (double rod, adjustable stroke).
The 3927 N push at 0.5 MPa clamps large press dies and fixtures, and the 175 mm stroke clears die changes on a 100-300 ton press bed.
The 25 mm chromed rod and fixed TPU bumpers handle frequent full-stroke cycling on refractory gates and sand chutes at 30-500 mm/s.
At this force class, bore 100 delivers 3927 N push at 0.5 MPa; step down to bore 80 (2513.3 N) for lighter clamping or up from bore 63 (1558.6 N) when your load needs this ceiling. Remember the piston drifts when air is lost, so add a rod lock or pilot check valve if the load must stay put. Mount with FA/FB flange, LB foot, CA/CB clevis, CR, SDB pivot or FTC brackets on the ISO 21287 face, and order -S if CMSE/DMSE switches are planned. Since ACP100X175 is discontinued, spec ACE100X175 and confirm the ISO 21287 mounting dimensions before swapping.
Replacement checklist
At 0.5 MPa it pushes 3927 N and pulls 3681.6 N; at 0.7 MPa it pushes 5497.8 N and pulls 5154.2 N. Theoretical maximum is 800.9 kgf at 1.0 MPa. It is double acting with a 100 mm bore, 175 mm stroke, 25 mm rod, 1/4" ports and a female M16x1.5 rod thread.
Order ACE100X175, the current ISO 21287 successor: swap the P for an E and you get the same bore, stroke and force class in a short compact body. Confirm the ISO 21287 mounting dimensions against your fixture first, since the ACP was built to the older DIN standard. The -S magnet option for CMSE/DMSE switches carries over as an order code.
Send us the quantity and destination. We confirm price, stock and lead time on the ACE100X175 replacement — usually within 7-8 hours.