This model is discontinued
AirTAC has phased out the ACP series. You can still order this code here: we ship the current replacement ACE100X60SB, the same code under the new prefix. The ACE replacement is a current-production ISO 21287 compact cylinder in the same bore, stroke and force class, with a matching short body and the same mounting-accessory family, so it fits the same envelope. Confirm mounting-interface dimensions against the ACE datasheet before ordering.
Airtac ACP Compact Cylinder ACP100X60SB
The AirTAC ACP Compact Cylinder ACP100X60SB is a double acting DIN-standard tight/compact air cylinder with a Ø100mm bore and 60mm stroke, 1/4" air ports and a hard-anodized aluminium body. This model is discontinued — the current-production replacement is the ACE100X60SB (ISO 21287 ACE), in the same bore, stroke and force class.
- BoreØ100 mm
- Stroke60 mm
- Port size1/4"
- Acting typeDouble acting
- Rod threadM16×1.5
- StatusDiscontinued → ACE100X60SB
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac ACP Compact Cylinder ACP100X60SB
Double acting on a 100 mm bore, the ACP100X60SB delivers 3927 N push and 3681.6 N pull at 0.5 MPa, rising to 5497.8 N push at 0.7 MPa, with a theoretical peak of 800.9 kgf at 1.0 MPa. The 60 mm stroke keeps the body short, and because the ISO 21287-class build saves roughly half the mounting length of an ISO 15552 profile cylinder, it slots into heavy presses and gantries where a full-length body cannot. The male rod thread (B code) and the optional -S magnet, fitted on this model for CMSE / DMSE switches, make integration straightforward.
Construction is a hard-anodized aluminium body with an S45C hard-chrome 25 mm rod and a fixed TPU bumper at each end. Note that this model is discontinued: the current-production direct is ACE100X60, so confirm the ISO 21287 mounting dimensions before swapping, since the ACP follows the DIN standard.
Airtac ACP Compact Cylinder ACP100X60SB Technical Specifications
| Model | Airtac ACP Compact Cylinder ACP100X60SB |
|---|---|
| Series | ACP DIN compact cylinder (discontinued) |
| Replacement | ACE100X60SB |
| Bore size | Ø100 mm |
| Stroke | 60 mm |
| Acting type | Double acting |
| Port size | 1/4" |
| Rod thread | M16×1.5 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 500 mm/s |
| Cushion | Fixed bumper (both ends) |
| Max standard stroke | Up to 300 mm |
Specifications follow the official AirTAC ACP datasheet (now discontinued). The ACE100X60SB (ISO 21287) carries the same bore/stroke/force class; confirm mounting-interface dimensions against the ACE datasheet before installation. Rod type: female thread (blank) or male thread (B). Thread options: PT (blank) / G.
Theoretical Output Force (Ø100mm)
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 3927 N | 3682 N |
| 0.7 MPa | 5498 N | 5154 N |
| Max (@1.0 MPa) | 801 kgf | |
The ACE100X60SB produces the same force from the same bore. Actual usable force is lower than theoretical; size with a margin.
Model Code: Airtac ACP Compact Cylinder ACP100X60SB
| ACP | DIN compact cylinder (double-acting, discontinued). |
|---|---|
| 100 | Bore size in mm. |
| ×60 | Stroke length in mm. |
| S | Optional built-in magnet for sensor position sensing (omit for no magnet). |
| B | Rod type: B = male thread; blank = female thread. |
Replacement mapping (swap P for E): ACP→ACE, ASP→ASE, ATP→ATE, ACPD→ACED, ACPJ→ACEJ. ACP-family: ACP (double acting), ASP / ATP (single acting push / pull), ACPD (double rod), ACPJ (double rod, adjustable stroke).
Where the Airtac ACP Compact Cylinder ACP100X60SB Is Used
Pneumatic press head
A 60 mm stroke pressing bearings into housings on a short-stroke bench press, where 3927 N at 0.5 MPa is enough and the compact body fits under a fixed frame.
Pallet clamp actuator
Clamping palletized cartons on a warehouse conveyor stopper, using the male rod thread with an I knuckle to swing the clamp arm into place.
Gate driver on a foundry line
Sliding a heavy sand-mould gate in a casting cell, where the 100 mm bore pushes the gate and the -S magnet feeds position feedback to the PLC via a DMSE switch.
Replacing the Airtac ACP Compact Cylinder ACP100X60SB with the ACE100X60SB
At this bore size the step either way is large: a 80 mm bore gives 2513.3 N push at 0.5 MPa, while stepping up is not possible within the range, so 100 mm is the top of the family. If the load needs to stay put when air is lost, add a rod lock or pilot check valve, because the piston drifts once pressure drops. This unit already carries the -S magnet for CMSE / DMSE switches, and FA/FB flange, LB foot or CA/CB clevis mounts bolt to the same face. Order ACE100X60 as the current replacement.
Replacement checklist
- ✓ Current-production ACE → ACE100X60SB
- ✓ Same bore / stroke / force class
- ✓ Confirm ISO 21287 mounting dimensions
- ✓ Port/thread type (PT / G)
- ✓ Add -S for magnet if you need sensors
Airtac ACP Compact Cylinder ACP100X60SB FAQ
Push is 3927 N and pull is 3681.6 N at 0.5 MPa; at 0.7 MPa push reaches 5497.8 N and pull 5154.2 N, with a theoretical maximum of 800.9 kgf at 1.0 MPa. Operating pressure is 0.15-1.0 MPa (22-145 psi), proof pressure 1.5 MPa (215 psi), speed 30-500 mm/s, temperature -20 to +70 C, and the port is 1/4" (PT thread).
Order ACE100X60, the current-production ISO 21287 successor: swap the P for an E and you get the same 100 mm bore, 60 mm stroke and force class in a short body. Because the ACP is DIN-standard, confirm the ISO 21287 mounting dimensions and the FA/FB, LB or CA/CB mounting interface before swapping.
Related AirTAC ACE Cylinders
Request a Quote for the ACE100X60SB
Send us the quantity and destination. We confirm price, stock and lead time on the ACE100X60SB replacement — usually within 7-8 hours.