This model is discontinued
AirTAC has phased out the ACP series. You can still order this code here: we ship the current replacement ACE100X75B, the same code under the new prefix. The ACE replacement is a current-production ISO 21287 compact cylinder in the same bore, stroke and force class, with a matching short body and the same mounting-accessory family, so it fits the same envelope. Confirm mounting-interface dimensions against the ACE datasheet before ordering.
Airtac ACP Compact Cylinder ACP100X75B
The AirTAC ACP Compact Cylinder ACP100X75B is a double acting DIN-standard tight/compact air cylinder with a Ø100mm bore and 75mm stroke, 1/4" air ports and a hard-anodized aluminium body. This model is discontinued — the current-production replacement is the ACE100X75B (ISO 21287 ACE), in the same bore, stroke and force class.
- BoreØ100 mm
- Stroke75 mm
- Port size1/4"
- Acting typeDouble acting
- Rod threadM16×1.5
- StatusDiscontinued → ACE100X75B
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac ACP Compact Cylinder ACP100X75B
The ACP100X75B is a double acting DIN-standard compact cylinder with a 100 mm bore and 75 mm stroke, driving a 25 mm hard-chromed S45C rod through a male thread (the B code). At 0.5 MPa it pushes 3927 N and pulls 3681.6 N, rising to 5497.8 N and 5154.2 N at 0.7 MPa - a theoretical peak of 800.9 kgf at 1.0 MPa. Its short ISO 21287-class body saves roughly 50% of the mounting length of an ISO 15552 profile cylinder, so a 100 mm bore fits clamping stations and press fixtures that cannot accept a full-length body.
Air runs at 0.15-1.0 MPa (22-145 psi), filtered to 40 um, with rod speed between 30 and 500 mm/s and fixed TPU bumpers at both ends. Note this model is discontinued: the current-production direct is ACE100X75, so confirm the ISO 21287 mounting dimensions before swapping.
Airtac ACP Compact Cylinder ACP100X75B Technical Specifications
| Model | Airtac ACP Compact Cylinder ACP100X75B |
|---|---|
| Series | ACP DIN compact cylinder (discontinued) |
| Replacement | ACE100X75B |
| Bore size | Ø100 mm |
| Stroke | 75 mm |
| Acting type | Double acting |
| Port size | 1/4" |
| Rod thread | M16×1.5 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 500 mm/s |
| Cushion | Fixed bumper (both ends) |
| Max standard stroke | Up to 300 mm |
Specifications follow the official AirTAC ACP datasheet (now discontinued). The ACE100X75B (ISO 21287) carries the same bore/stroke/force class; confirm mounting-interface dimensions against the ACE datasheet before installation. Rod type: female thread (blank) or male thread (B). Thread options: PT (blank) / G.
Theoretical Output Force (Ø100mm)
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 3927 N | 3682 N |
| 0.7 MPa | 5498 N | 5154 N |
| Max (@1.0 MPa) | 801 kgf | |
The ACE100X75B produces the same force from the same bore. Actual usable force is lower than theoretical; size with a margin.
Model Code: Airtac ACP Compact Cylinder ACP100X75B
| ACP | DIN compact cylinder (double-acting, discontinued). |
|---|---|
| 100 | Bore size in mm. |
| ×75 | Stroke length in mm. |
| S | Optional built-in magnet for sensor position sensing (omit for no magnet). |
| B | Rod type: B = male thread; blank = female thread. |
Replacement mapping (swap P for E): ACP→ACE, ASP→ASE, ATP→ATE, ACPD→ACED, ACPJ→ACEJ. ACP-family: ACP (double acting), ASP / ATP (single acting push / pull), ACPD (double rod), ACPJ (double rod, adjustable stroke).
Where the Airtac ACP Compact Cylinder ACP100X75B Is Used
Stamping die clamp
The 3927 N push at 0.5 MPa locks stamping die clamps in a press shop, and the 75 mm stroke clears die changes without a long body in the bolster area.
Short-stroke press fit
A 75 mm stroke at up to 5497.8 N at 0.7 MPa presses bushings and bearings in an automotive assembly cell where a full-length cylinder will not fit.
Replacing the Airtac ACP Compact Cylinder ACP100X75B with the ACE100X75B
At 3927 N push at 0.5 MPa, the 100 mm bore suits heavy clamping and short-stroke pressing; step down to the 80 mm bore (2513.3 N) for lighter dies or accept the larger frame when you need the full 800.9 kgf class. The 75 mm stroke sits well inside the 300 mm maximum standard stroke for this bore. The B code gives a male rod thread on the 25 mm rod with a PT port thread; FA/FB flange, LB foot and CA/CB clevis mounts bolt to the same face. A plain cylinder drifts when air is lost, so add a rod lock or pilot check valve for held loads. This model is discontinued - order ACE100X75 as the current direct and verify the ISO 21287 mounting dimensions.
Replacement checklist
- ✓ Current-production ACE → ACE100X75B
- ✓ Same bore / stroke / force class
- ✓ Confirm ISO 21287 mounting dimensions
- ✓ Port/thread type (PT / G)
- ✓ Add -S for magnet if you need sensors
Airtac ACP Compact Cylinder ACP100X75B FAQ
Push is 3927 N and pull 3681.6 N at 0.5 MPa; at 0.7 MPa push reaches 5497.8 N and pull 5154.2 N, with a theoretical maximum of 800.9 kgf at 1.0 MPa. It is a double acting compact cylinder, 100 mm bore, 75 mm stroke, 25 mm rod with male thread, 1/4" PT port, 0.15-1.0 MPa (22-145 psi) operating pressure, 30-500 mm/s speed and fixed TPU bumpers at both ends.
Order ACE100X75: swap the P for an E and you get the current-production ISO 21287 successor in the same bore, stroke and force class. Because the ACP was built to a DIN standard, confirm the ISO 21287 mounting dimensions against your fixture before swapping. If you need position sensing, the ACE family takes the optional magnet with CMSE / DMSE switches.
Related AirTAC ACE Cylinders
Request a Quote for the ACE100X75B
Send us the quantity and destination. We confirm price, stock and lead time on the ACE100X75B replacement — usually within 7-8 hours.