This model is discontinued
AirTAC has phased out the ACP series. You can still order this code here: we ship the current replacement ACE100X75SB, the same code under the new prefix. The ACE replacement is a current-production ISO 21287 compact cylinder in the same bore, stroke and force class, with a matching short body and the same mounting-accessory family, so it fits the same envelope. Confirm mounting-interface dimensions against the ACE datasheet before ordering.

The AirTAC ACP Compact Cylinder ACP100X75SB is a double acting DIN-standard tight/compact air cylinder with a Ø100mm bore and 75mm stroke, 1/4" air ports and a hard-anodized aluminium body. This model is discontinued — the current-production replacement is the ACE100X75SB (ISO 21287 ACE), in the same bore, stroke and force class.
A double acting compact cylinder with a 100 mm bore and 75 mm stroke, the ACP100X75SB delivers 3927 N push and 3681.6 N pull at 0.5 MPa, rising to 5497.8 N push at 0.7 MPa. Its hard-anodized aluminium body carries a 25 mm S45C hard-chrome rod with a male thread, and a fixed TPU bumper sits at both ends. The short ISO 21287-class body saves about 50% of the mounting length of an ISO 15552 profile cylinder, so it slots into heavy presses, clamping fixtures and gantries where a full-length body cannot. The S in the code means the optional -S magnet is fitted, so CMSE or DMSE reed and solid-state switches can be mounted for end-position sensing.
Note this model is discontinued; the current-production direct is ACE100X75, matching the same bore, stroke and force class. Confirm the ISO 21287 mounting dimensions before swapping, since the ACP was built to the DIN standard. Air supply should be filtered to 40 um, 0.15-1.0 MPa (22-145 psi), with speed between 30 and 500 mm/s.
| Model | Airtac ACP Compact Cylinder ACP100X75SB |
|---|---|
| Series | ACP DIN compact cylinder (discontinued) |
| Replacement | ACE100X75SB |
| Bore size | Ø100 mm |
| Stroke | 75 mm |
| Acting type | Double acting |
| Port size | 1/4" |
| Rod thread | M16×1.5 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 500 mm/s |
| Cushion | Fixed bumper (both ends) |
| Max standard stroke | Up to 300 mm |
Specifications follow the official AirTAC ACP datasheet (now discontinued). The ACE100X75SB (ISO 21287) carries the same bore/stroke/force class; confirm mounting-interface dimensions against the ACE datasheet before installation. Rod type: female thread (blank) or male thread (B). Thread options: PT (blank) / G.
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 3927 N | 3682 N |
| 0.7 MPa | 5498 N | 5154 N |
| Max (@1.0 MPa) | 801 kgf | |
The ACE100X75SB produces the same force from the same bore. Actual usable force is lower than theoretical; size with a margin.
| ACP | DIN compact cylinder (double-acting, discontinued). |
|---|---|
| 100 | Bore size in mm. |
| ×75 | Stroke length in mm. |
| S | Optional built-in magnet for sensor position sensing (omit for no magnet). |
| B | Rod type: B = male thread; blank = female thread. |
Replacement mapping (swap P for E): ACP→ACE, ASP→ASE, ATP→ATE, ACPD→ACED, ACPJ→ACEJ. ACP-family: ACP (double acting), ASP / ATP (single acting push / pull), ACPD (double rod), ACPJ (double rod, adjustable stroke).
The 3927 N push at 0.5 MPa (5497.8 N at 0.7 MPa) suits short-stroke crimping, staking and swaging heads on aluminium extrusion lines where the 75 mm stroke is enough for the full die travel.
With about 2356 N of practical clamping force at 0.5 MPa, this cylinder locks cast-iron housings into drilling and milling fixtures, and the short body fits inside tight fixture plates.
In warehouse gate and stopper systems, the cylinder swings or lifts loaded pallet gates, and the fitted -S magnet with a DMSE switch confirms gate-open position to the PLC.
At this force class the 100 mm bore is near the top of the range: it pushes 3927 N at 0.5 MPa versus 2513.3 N for the 80 mm bore, so step down to 80 only if your load is under about 1500 N of real work. There is no larger standard bore, so if 3927 N is marginal at your working pressure, consider dual cylinders or a larger custom bore. The 75 mm stroke sits well inside the 300 mm maximum standard stroke for this bore. Choose the B male rod thread when your tooling screws onto the rod; FA/FB flange, LB foot or CA/CB clevis mounts bolt to the same face. If the load must stay put when air is lost, add a rod lock or pilot check valve, since the piston will drift. Order ACE100X75 as the current replacement and verify ISO 21287 mounting dimensions.
Replacement checklist
At 0.5 MPa it pushes 3927 N and pulls 3681.6 N; at 0.7 MPa those rise to 5497.8 N push and 5154.2 N pull. The theoretical maximum is 800.9 kgf at 1.0 MPa. Operating range is 0.15-1.0 MPa (22-145 psi), proof 1.5 MPa (215 psi), speed 30-500 mm/s, temperature -20 to +70 C, with a 1/4" port and a 25 mm male-thread rod.
No, the ACP family is discontinued. The current-production direct is ACE100X75, the ISO 21287 successor with the same 100 mm bore, 75 mm stroke and force class, plus the same FA/FB flange, LB foot and CA/CB clevis mounting family. Because the ACP was DIN-standard, confirm the ISO 21287 mounting dimensions before you swap. The fixed TPU bumpers at both ends simply decelerate the piston at each end of travel.
Send us the quantity and destination. We confirm price, stock and lead time on the ACE100X75SB replacement — usually within 7-8 hours.