This model is discontinued
AirTAC has phased out the ACP series. You can still order this code here: we ship the current replacement ACE12X110, the same code under the new prefix. The ACE replacement is a current-production ISO 21287 compact cylinder in the same bore, stroke and force class, with a matching short body and the same mounting-accessory family, so it fits the same envelope. Confirm mounting-interface dimensions against the ACE datasheet before ordering.
Airtac ACP Compact Cylinder ACP12X110
The AirTAC ACP Compact Cylinder ACP12X110 is a double acting DIN-standard tight/compact air cylinder with a Ø12mm bore and 110mm stroke, M5×0.8 air ports and a hard-anodized aluminium body. This model is discontinued — the current-production replacement is the ACE12X110 (ISO 21287 ACE), in the same bore, stroke and force class.
- BoreØ12 mm
- Stroke110 mm
- Port sizeM5×0.8
- Acting typeDouble acting
- Rod threadM3×0.5
- StatusDiscontinued → ACE12X110
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac ACP Compact Cylinder ACP12X110
A double acting compact cylinder in the DIN-standard ACP series, the ACP12X110 pairs a 12 mm bore with a 110 mm stroke and a 6 mm rod. At 0.5 MPa it pushes 56.5 N and pulls 42.4 N, rising to 79.2 N push at 0.7 MPa, with a theoretical ceiling of 11.5 kgf at 1.0 MPa. The 110 mm stroke is longer than the 50 mm standard limit for this bore, so it is a made-to-order build. The hard-anodized aluminium body with an S45C hard-chrome rod runs on air filtered to 40 um at 0.15-1.0 MPa (22-145 psi), 30-500 mm/s.
Because the short ISO 21287-class body saves roughly 50% of the mounting length of an ISO 15552 profile cylinder, it slots into slim fixtures and small gantries. Note the fixed TPU bumper at each end only softens end-of-travel; it never holds a load when air is lost, so add a rod lock or check valve if you need position holding. This model is discontinued - the current direct is ACE12X110, so confirm ISO 21287 mounting dimensions before swapping.
Airtac ACP Compact Cylinder ACP12X110 Technical Specifications
| Model | Airtac ACP Compact Cylinder ACP12X110 |
|---|---|
| Series | ACP DIN compact cylinder (discontinued) |
| Replacement | ACE12X110 |
| Bore size | Ø12 mm |
| Stroke | 110 mm |
| Acting type | Double acting |
| Port size | M5×0.8 |
| Rod thread | M3×0.5 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 500 mm/s |
| Cushion | Fixed bumper (both ends) |
| Max standard stroke | Up to 50 mm |
Specifications follow the official AirTAC ACP datasheet (now discontinued). The ACE12X110 (ISO 21287) carries the same bore/stroke/force class; confirm mounting-interface dimensions against the ACE datasheet before installation. Rod type: female thread (blank) or male thread (B). Thread options: PT (blank) / G.
Theoretical Output Force (Ø12mm)
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 57 N | 42 N |
| 0.7 MPa | 79 N | 59 N |
| Max (@1.0 MPa) | 12 kgf | |
The ACE12X110 produces the same force from the same bore. Actual usable force is lower than theoretical; size with a margin.
Model Code: Airtac ACP Compact Cylinder ACP12X110
| ACP | DIN compact cylinder (double-acting, discontinued). |
|---|---|
| 12 | Bore size in mm. |
| ×110 | Stroke length in mm. |
| S | Optional built-in magnet for sensor position sensing (omit for no magnet). |
| B | Rod type: B = male thread; blank = female thread. |
Replacement mapping (swap P for E): ACP→ACE, ASP→ASE, ATP→ATE, ACPD→ACED, ACPJ→ACEJ. ACP-family: ACP (double acting), ASP / ATP (single acting push / pull), ACPD (double rod), ACPJ (double rod, adjustable stroke).
Where the Airtac ACP Compact Cylinder ACP12X110 Is Used
Lab sample ejector
Ejects microplate or vial samples from a compact analytical fixture where a 56.5 N push at 0.5 MPa and a slim 12 mm body are enough.
Small-part ejection on assembly benches
Pushes finished clips or pins off a jig after forming; the long 110 mm made-to-order stroke clears deep pockets in tight bench tooling.
Position-flagged light gate actuator
With the optional -S magnet and a CMSE or DMSE switch, it flags end-of-travel on a small inspection station running at 30-500 mm/s.
Replacing the Airtac ACP Compact Cylinder ACP12X110 with the ACE12X110
At 12 mm bore you are at the light end of the range: 56.5 N push at 0.5 MPa versus 100.5 N from a 16 mm bore and 157.1 N from a 20 mm. If your part or clamp force sits near 34 N usable, this size works; step up to 16 mm for margin. The 110 mm stroke is non-standard for this bore (50 mm max standard), so order it as a made-to-order unit. The rod ends in a female M3x0.5 thread and ports are M5x0.8. No magnet is fitted on this code - add the -S option if you want CMSE or DMSE switch sensing. For new projects, specify the ACE12X110 instead, matching bore, stroke and force class.
Replacement checklist
- ✓ Current-production ACE → ACE12X110
- ✓ Same bore / stroke / force class
- ✓ Confirm ISO 21287 mounting dimensions
- ✓ Port/thread type (PT / G)
- ✓ Add -S for magnet if you need sensors
Airtac ACP Compact Cylinder ACP12X110 FAQ
At 0.5 MPa it pushes 56.5 N and pulls 42.4 N; at 0.7 MPa, 79.2 N push and 59.4 N pull. Theoretical maximum is 11.5 kgf at 1.0 MPa. Operating range is 0.15-1.0 MPa (22-145 psi) with 1.5 MPa (215 psi) proof pressure, air filtered to 40 um, speed 30-500 mm/s and -20 to +70 C.
Standard strokes for bore 12 stop at 50 mm, so 110 mm is a made-to-order build. This ACP model is discontinued; the current-production replacement is ACE12X110 (swap the P for an E), which matches the same bore, stroke and force class in the ISO 21287 family. Confirm the ISO 21287 mounting dimensions against your fixture before swapping, since the ACP was built to the DIN standard.
Request a Quote for the ACE12X110
Send us the quantity and destination. We confirm price, stock and lead time on the ACE12X110 replacement — usually within 7-8 hours.