This model is discontinued
AirTAC has phased out the ACP series. You can still order this code here: we ship the current replacement ACE80X15B, the same code under the new prefix. The ACE replacement is a current-production ISO 21287 compact cylinder in the same bore, stroke and force class, with a matching short body and the same mounting-accessory family, so it fits the same envelope. Confirm mounting-interface dimensions against the ACE datasheet before ordering.
Airtac ACP Compact Cylinder ACP80X15B
The AirTAC ACP Compact Cylinder ACP80X15B is a double acting DIN-standard tight/compact air cylinder with a Ø80mm bore and 15mm stroke, 1/4" air ports and a hard-anodized aluminium body. This model is discontinued — the current-production replacement is the ACE80X15B (ISO 21287 ACE), in the same bore, stroke and force class.
- BoreØ80 mm
- Stroke15 mm
- Port size1/4"
- Acting typeDouble acting
- Rod threadM12×1.75
- StatusDiscontinued → ACE80X15B
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac ACP Compact Cylinder ACP80X15B
The ACP80X15B is a double acting DIN-standard compact cylinder with an 80 mm bore and a short 15 mm stroke, built on a hard-anodized aluminium body with an S45C hard-chrome 20 mm rod and a male rod thread (the B code). Air drives the piston both ways, and fixed TPU bumpers at each end take the end-of-travel shock. At 0.5 MPa it pushes 2513.3 N and pulls 2356.2 N; at 0.7 MPa that rises to 3518.6 N push and 3298.7 N pull, with a theoretical peak of 512.6 kgf at 1.0 MPa. The short ISO 21287-class body saves about 50% of the mounting length of an ISO 15552 profile cylinder, so it slots into tight presses, clamping fixtures and gantry frames.
Note that it does not hold position if air is lost; pair it with a rod lock or pilot check valve for a held load. This model is discontinued: the current-production direct is ACE80X15, same bore, stroke and force class - confirm the ISO 21287 mounting dimensions before swapping.
Airtac ACP Compact Cylinder ACP80X15B Technical Specifications
| Model | Airtac ACP Compact Cylinder ACP80X15B |
|---|---|
| Series | ACP DIN compact cylinder (discontinued) |
| Replacement | ACE80X15B |
| Bore size | Ø80 mm |
| Stroke | 15 mm |
| Acting type | Double acting |
| Port size | 1/4" |
| Rod thread | M12×1.75 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 500 mm/s |
| Cushion | Fixed bumper (both ends) |
| Max standard stroke | Up to 300 mm |
Specifications follow the official AirTAC ACP datasheet (now discontinued). The ACE80X15B (ISO 21287) carries the same bore/stroke/force class; confirm mounting-interface dimensions against the ACE datasheet before installation. Rod type: female thread (blank) or male thread (B). Thread options: PT (blank) / G.
Theoretical Output Force (Ø80mm)
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 2513 N | 2356 N |
| 0.7 MPa | 3519 N | 3299 N |
| Max (@1.0 MPa) | 513 kgf | |
The ACE80X15B produces the same force from the same bore. Actual usable force is lower than theoretical; size with a margin.
Model Code: Airtac ACP Compact Cylinder ACP80X15B
| ACP | DIN compact cylinder (double-acting, discontinued). |
|---|---|
| 80 | Bore size in mm. |
| ×15 | Stroke length in mm. |
| S | Optional built-in magnet for sensor position sensing (omit for no magnet). |
| B | Rod type: B = male thread; blank = female thread. |
Replacement mapping (swap P for E): ACP→ACE, ASP→ASE, ATP→ATE, ACPD→ACED, ACPJ→ACEJ. ACP-family: ACP (double acting), ASP / ATP (single acting push / pull), ACPD (double rod), ACPJ (double rod, adjustable stroke).
Where the Airtac ACP Compact Cylinder ACP80X15B Is Used
Short-stroke press clamp
The 15 mm stroke and 2513.3 N push at 0.5 MPa suit a bench-top clamping fixture that locks a machined aluminium housing against a hard stop on every cycle.
Case squaring pusher
A packaging line end stop uses the short body to square cartons against a rail, with the 1/4" port fed at 0.5 MPa for consistent 30-500 mm/s travel.
Replacing the Airtac ACP Compact Cylinder ACP80X15B with the ACE80X15B
If 2513.3 N of push at 0.5 MPa is more than your job needs, step down to the ACP63 (1558.6 N push at 0.5 MPa); if you need more, the ACP100 delivers 3927 N at the same pressure. The 15 mm stroke sits well inside the 300 mm maximum standard stroke for the 80 mm bore. This unit has no magnet - order the -S code if you want CMSE or DMSE switches for end-of-stroke sensing. FA/FB flange, LB foot and CA/CB clevis mounts bolt to the standard face. Since ACP is discontinued, specify ACE80X15 as the current replacement and verify the ISO 21287 hole pattern first.
Replacement checklist
- ✓ Current-production ACE → ACE80X15B
- ✓ Same bore / stroke / force class
- ✓ Confirm ISO 21287 mounting dimensions
- ✓ Port/thread type (PT / G)
- ✓ Add -S for magnet if you need sensors
Airtac ACP Compact Cylinder ACP80X15B FAQ
At 0.5 MPa it pushes 2513.3 N and pulls 2356.2 N; at 0.7 MPa it reaches 3518.6 N push and 3298.7 N pull, with a theoretical maximum of 512.6 kgf at 1.0 MPa. The model is discontinued - the current-production replacement is ACE80X15 (swap the P for an E), which matches the same bore, stroke and force class. Confirm the ISO 21287 mounting dimensions before swapping, since ACP was built to the DIN standard.
The short ISO 21287-class body saves about 50% of the mounting length of an ISO 15552 profile cylinder, so it fits shallow fixtures and guard spaces. Sensing is not fitted on this code: the magnet is the optional -S suffix, and only with -S can CMSE or DMSE reed or solid-state switches be clipped on. Mounting options include FA/FB flange, LB foot and CA/CB clevis.
Request a Quote for the ACE80X15B
Send us the quantity and destination. We confirm price, stock and lead time on the ACE80X15B replacement — usually within 7-8 hours.