This model is discontinued
AirTAC has phased out the ACP series. You can still order this code here: we ship the current replacement ACED12X50, the same code under the new prefix. The ACE replacement is a current-production ISO 21287 compact cylinder in the same bore, stroke and force class, with a matching short body and the same mounting-accessory family, so it fits the same envelope. Confirm mounting-interface dimensions against the ACE datasheet before ordering.
Airtac ACPD Double Rod Compact Cylinder ACPD12X50
The AirTAC ACPD Double Rod Compact Cylinder ACPD12X50 is a double acting, double rod DIN-standard tight/compact air cylinder with a Ø12mm bore and 50mm stroke, M5×0.8 air ports and a hard-anodized aluminium body. This model is discontinued — the current-production replacement is the ACED12X50 (ISO 21287 ACE), in the same bore, stroke and force class.
- BoreØ12 mm
- Stroke50 mm
- Port sizeM5×0.8
- Acting typeDouble acting, double rod
- Rod threadM3×0.5
- StatusDiscontinued → ACED12X50
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac ACPD Double Rod Compact Cylinder ACPD12X50
A double acting compact cylinder with a rod leaving both covers, the ACPD12X50 pushes and pulls with identical force - 42.4 N at 0.5 MPa and 59.4 N at 0.7 MPa in either direction, since both strokes work on the rod-side area of the 12 mm bore. The through-rod resists rotation and light side load, gives a symmetric mounting point at each end, and the rear rod can carry a sensor flag. A fixed TPU bumper sits at both covers, and speed spans 30-500 mm/s.
The short ISO 21287-class body saves roughly 50% of the mounting length of an ISO 15552 profile cylinder, so it slots into slim fixtures, small gates and compact test rigs. For planning, treat about 25 N (roughly 2.5 kg vertical) as the usable working force at 0.5 MPa instead of the full rating. Note this model is discontinued: the current-production direct is the ACED12X50, so confirm ISO 21287 mounting dimensions before swapping.
Airtac ACPD Double Rod Compact Cylinder ACPD12X50 Technical Specifications
| Model | Airtac ACPD Double Rod Compact Cylinder ACPD12X50 |
|---|---|
| Series | ACPD DIN compact cylinder (discontinued) |
| Replacement | ACED12X50 |
| Bore size | Ø12 mm |
| Stroke | 50 mm |
| Acting type | Double acting, double rod |
| Port size | M5×0.8 |
| Rod thread | M3×0.5 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 500 mm/s |
| Cushion | Fixed bumper (both ends) |
| Max standard stroke | Up to 50 mm |
Specifications follow the official AirTAC ACP datasheet (now discontinued). The ACED12X50 (ISO 21287) carries the same bore/stroke/force class; confirm mounting-interface dimensions against the ACE datasheet before installation. Rod type: female thread (blank) or male thread (B). Thread options: PT (blank) / G.
Theoretical Output Force (Ø12mm)
| Pressure | Force (both ways) |
|---|---|
| 0.5 MPa | 42 N |
| 0.7 MPa | 59 N |
| Max (@1.0 MPa) | 9 kgf |
Double-rod: a rod exits both covers, so output force is equal in both directions (rod-side area used).
Model Code: Airtac ACPD Double Rod Compact Cylinder ACPD12X50
| ACPD | DIN compact cylinder (double-rod, discontinued). |
|---|---|
| 12 | Bore size in mm. |
| ×50 | Stroke length in mm. |
| S | Optional built-in magnet for sensor position sensing (omit for no magnet). |
| B | Rod type: B = male thread; blank = female thread. |
Replacement mapping (swap P for E): ACP→ACE, ASP→ASE, ATP→ATE, ACPD→ACED, ACPJ→ACEJ. ACP-family: ACP (double acting), ASP / ATP (single acting push / pull), ACPD (double rod), ACPJ (double rod, adjustable stroke).
Where the Airtac ACPD Double Rod Compact Cylinder ACPD12X50 Is Used
Presence flag on the rear rod
The second rod at the back cover carries a flag past a switch on small assembly stations, giving a position signal without extra hardware - order the -S code if CMSE or DMSE switches are wanted.
Light-duty clamping of small parts
With about 25 N of practical working force at 0.5 MPa, it clamps electronics housings, small brackets or PCB fixtures where heavier force would mark the part.
Push-pull indexing in tight cells
Equal force both ways plus a body about 50% shorter than an ISO 15552 profile cylinder makes it handy for reciprocating slides inside cramped laboratory or packaging equipment.
Replacing the Airtac ACPD Double Rod Compact Cylinder ACPD12X50 with the ACED12X50
At 42.4 N per direction, this bore suits light clamping, positioning and sensor-flag duty rather than heavy pressing. If your load needs more, the 16 mm bore delivers 75.4 N at 0.5 MPa; if less is fine, check whether a smaller actuator or a lever mechanism covers it. The 50 mm stroke sits at the maximum standard stroke for bore 12, so no made-to-order length is needed. Rod end is female M3x0.5 and ports are M5x0.8 PT. A plain double-rod cylinder drifts when air is lost - add a rod lock or pilot check if the load must stay put. This unit is discontinued; the ACED12X50 is the current replacement in the same force class.
Replacement checklist
- ✓ Current-production ACE → ACED12X50
- ✓ Same bore / stroke / force class
- ✓ Confirm ISO 21287 mounting dimensions
- ✓ Port/thread type (PT / G)
- ✓ Add -S for magnet if you need sensors
Airtac ACPD Double Rod Compact Cylinder ACPD12X50 FAQ
No - the rod exits both covers, so force is equal in both directions: 42.4 N at 0.5 MPa and 59.4 N at 0.7 MPa, with a maximum of 8.6 kgf at 1.0 MPa. Operating range is 0.15-1.0 MPa (22-145 psi), proof pressure 1.5 MPa (215 psi), speed 30-500 mm/s, and the port is M5x0.8. In practice plan on roughly 25 N (about 2.5 kg vertical) for real work at 0.5 MPa.
Order the ACED12X50, the current-production ISO 21287 successor: swap the P for an E and you get the same 12 mm bore, 50 mm stroke and force class with a matching short body and mounting family (FA/FB flange, LB foot and more). Because the ACP is DIN-standard, confirm the ISO 21287 mounting dimensions against your fixture before swapping. The optional -S magnet code enables CMSE / DMSE switches on the replacement.
Request a Quote for the ACED12X50
Send us the quantity and destination. We confirm price, stock and lead time on the ACED12X50 replacement — usually within 7-8 hours.