Airtac Adjustable Cylinder SAIJ32 SAIJ32BX550-10S
The AirTAC Adjustable Cylinder SAIJ32 SAIJ32BX550-10S is a genuine double-acting ISO 15552 profile-barrel air cylinder with a Ø32mm bore and 550mm stroke, G1/8 air ports and adjustable end cushioning. Its standardized mounting interface makes it interchangeable with other ISO 15552 cylinders at the mounting interface.
- BoreØ32 mm
- Stroke550 mm
- Port sizeG1/8
- Acting typeDouble acting
- Rod threadM10×1.25
- CushionAdjustable, 27 mm
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac Adjustable Cylinder SAIJ32 SAIJ32BX550-10S
The AirTAC SAIJ32X550-10-S is a double-acting ISO 15552 profile cylinder featuring a rear-mounted stroke adjuster. It provides a 540-550mm usable travel window, letting you dial back the nominal 550mm stroke by up to 10mm during machine commissioning without adding external stops.
This specific SKU includes a SUS304 stainless steel rod for superior corrosion resistance and comes pre-fitted with a magnet for CMSE reed and DMSE electronic sensors. The extruded aluminum barrel incorporates sensor grooves on both sides. While the rear adjuster fine-tunes the retract position, remember it acts only as a travel stop and does not hold the load without live air pressure.
Airtac Adjustable Cylinder SAIJ32 SAIJ32BX550-10S Technical Specifications
| Model | Airtac Adjustable Cylinder SAIJ32 SAIJ32BX550-10S |
|---|---|
| Series | SAI ISO 15552 profile cylinder |
| Bore size | Ø32 mm |
| Stroke | 550 mm |
| Acting type | Double acting |
| Port size | G1/8 |
| Rod thread | M10×1.25 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 27 mm |
| Max stroke | Up to 1000 mm |
Specifications follow the official AirTAC SAI series datasheet and ISO 15552 dimensions. Confirm against the product label before installation. Port options: G (BSPP) / NPT.
Theoretical Output Force (Ø32mm)
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 346 N | 346 N |
| 0.7 MPa | 484 N | — |
| Max (@1.0 MPa) | 70 kgf | |
Double-rod model: the rod passes through the rear cover, so both piston faces lose rod area and push is shown at the annular-area value. Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
Model Code: Airtac Adjustable Cylinder SAIJ32 SAIJ32BX550-10S
| SAI | ISO 15552 profile-barrel cylinder series. |
|---|---|
| 32 | Bore size in mm. |
| ×550 | Stroke length in mm. |
| -S | Optional built-in magnet for sensor position sensing. |
Related SAI-family variants: SAID (double rod), SAIJ (adjustable stroke), SAIL (with lock), SAIF (with valve), BSAI (enclasp / clamp-lock), and SAI-S with built-in magnet. Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B); seals: TPU (blank) / Viton H / NBR N.
Where the Airtac Adjustable Cylinder SAIJ32 SAIJ32BX550-10S Is Used
Machine Commissioning
Fine-tune the 540-550mm retract end-stop precisely during setup, absorbing mechanical tolerance variations without hardware changes.
Product Changeover
Quickly adjust the stroke by up to 10mm to accommodate slightly different product sizes on a packaging line.
Gripping & Pushing
Utilize the 12mm SUS304 stainless steel rod for light-duty pushing tasks in environments where corrosion resistance is required.
Is the Airtac Adjustable Cylinder SAIJ32 SAIJ32BX550-10S the Right Cylinder?
The 10mm adjustment window is ideal for product changeovers on a line, preventing the need to physically swap cylinders for minor length differences. If you need higher force, stepping up to a 40mm bore yields 628N, whereas dropping to a smaller bore would reduce your thrust significantly.
For any stroke length of 550mm, side-load management is critical. The 12mm rod and M10x1.25 thread handle moderate loads, but you must use an external guide to prevent rod binding over this extended travel. This SAIJ model uses a reduced mounting set (Basic, FA, LB, TC, FTC, TCM1, TCM2) and omits FB, CA, CB, and CR brackets. If your application requires true load-holding without continuous air supply, consider the SAIL or BSAI series instead.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Stroke and mounting space
- ✓ Port/thread type (PT/NPT/G)
- ✓ Magnet (-S) for sensors?
- ✓ Side load — consider a guided cylinder
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Avoid side load on the piston rod.
- check Adjust end cushion screws for smooth stops.
- check Use correct mounting accessory (FA/FB/CA/CB/LB/TC).
- check Installation by qualified personnel per AirTAC docs.
Airtac Adjustable Cylinder SAIJ32 SAIJ32BX550-10S FAQ
The rear adjuster acts as a mechanical stop that lets you shorten the effective stroke by up to 10mm, providing a 540-550mm travel window. It only sets the end position; it does not lock or hold the load without live air pressure.
The operating speed range is 30-800mm/s, and it features variable air cushions at both ends to decelerate the piston.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Request a Quote for Airtac Adjustable Cylinder SAIJ32 SAIJ32BX550-10S
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.