Airtac Adjustable Cylinder SAIJ32 SAIJ32BX900-30S
The AirTAC Adjustable Cylinder SAIJ32 SAIJ32BX900-30S is a genuine double-acting ISO 15552 profile-barrel air cylinder with a Ø32mm bore and 900mm stroke, G1/8 air ports and adjustable end cushioning. Its standardized mounting interface makes it interchangeable with other ISO 15552 cylinders at the mounting interface.
- BoreØ32 mm
- Stroke900 mm
- Port sizeG1/8
- Acting typeDouble acting
- Rod threadM10×1.25
- CushionAdjustable, 27 mm
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac Adjustable Cylinder SAIJ32 SAIJ32BX900-30S
The AirTAC SAIJ32X900-30-S is a double-acting, double-rod ISO 15552 profile cylinder equipped with a rear stroke adjuster. The integrated -S magnet enables seamless position detection with AirTAC CMSE reed or DMSE electronic solid-state sensors.
With a 900mm nominal stroke and a 30mm adjustment range, this model provides an exact 870-900mm usable travel window. This built-in rear stopper allows you to fine-tune the retract end position during commissioning without adding external stops or swapping the cylinder. The extruded aluminum barrel features sensor grooves on both sides, and the mounting set includes Basic, FA, LB, TC, FTC, TCM1, and TCM2.
Airtac Adjustable Cylinder SAIJ32 SAIJ32BX900-30S Technical Specifications
| Model | Airtac Adjustable Cylinder SAIJ32 SAIJ32BX900-30S |
|---|---|
| Series | SAI ISO 15552 profile cylinder |
| Bore size | Ø32 mm |
| Stroke | 900 mm |
| Acting type | Double acting |
| Port size | G1/8 |
| Rod thread | M10×1.25 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 27 mm |
| Max stroke | Up to 1000 mm |
Specifications follow the official AirTAC SAI series datasheet and ISO 15552 dimensions. Confirm against the product label before installation. Port options: G (BSPP) / NPT.
Theoretical Output Force (Ø32mm)
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 346 N | 346 N |
| 0.7 MPa | 484 N | — |
| Max (@1.0 MPa) | 70 kgf | |
Double-rod model: the rod passes through the rear cover, so both piston faces lose rod area and push is shown at the annular-area value. Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
Model Code: Airtac Adjustable Cylinder SAIJ32 SAIJ32BX900-30S
| SAI | ISO 15552 profile-barrel cylinder series. |
|---|---|
| 32 | Bore size in mm. |
| ×900 | Stroke length in mm. |
| -S | Optional built-in magnet for sensor position sensing. |
Related SAI-family variants: SAID (double rod), SAIJ (adjustable stroke), SAIL (with lock), SAIF (with valve), BSAI (enclasp / clamp-lock), and SAI-S with built-in magnet. Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B); seals: TPU (blank) / Viton H / NBR N.
Where the Airtac Adjustable Cylinder SAIJ32 SAIJ32BX900-30S Is Used
Commissioning Fine-Tuning
Dial in the exact retract position within the 870-900mm window during machine setup, eliminating the need to machine custom external spacers.
Product Size Changeover
Quickly adjust the end-stop by up to 30mm on packaging lines to accommodate varying carton lengths without changing out the actuator.
Long-Stroke Positioning
Verify exact end-of-travel limits on extended 900mm strokes using the integrated -S magnet alongside CMSE or DMSE sensors.
Is the Airtac Adjustable Cylinder SAIJ32 SAIJ32BX900-30S the Right Cylinder?
Choose this 32mm bore when an application requires precise end-position tuning within a 870-900mm travel window, avoiding the need to physically swap cylinders during product changeovers. If your setup needs greater thrust, stepping up to the 40mm bore increases push force to 628N at 0.5 MPa. Because the 900mm stroke is long relative to the 12mm rod diameter, an external guide is recommended to prevent excessive side-loading and premature seal wear.
As an adjustable-stroke alternative to the fixed SAI cylinder, the rear screw acts solely as a travel stop and does not hold the load without live air pressure. For load-holding requirements without continuous air, consider the SAIL or BSAI series. To match this ISO 15552 interchangeable cylinder exactly, specify the 32mm bore, 900mm stroke, 30mm adjustment, PT tapered port, SUS304 rod, and -S magnet.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Stroke and mounting space
- ✓ Port/thread type (PT/NPT/G)
- ✓ Magnet (-S) for sensors?
- ✓ Side load — consider a guided cylinder
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Avoid side load on the piston rod.
- check Adjust end cushion screws for smooth stops.
- check Use correct mounting accessory (FA/FB/CA/CB/LB/TC).
- check Installation by qualified personnel per AirTAC docs.
Airtac Adjustable Cylinder SAIJ32 SAIJ32BX900-30S FAQ
At 0.7 MPa, the push force increases to 563N.
The rear adjuster screw allows you to shorten the effective travel from the 900mm nominal stroke by up to 30mm, creating a usable 870-900mm window. It functions as a mechanical stop and does not lock the load without air pressure.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Request a Quote for Airtac Adjustable Cylinder SAIJ32 SAIJ32BX900-30S
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.