Airtac B06-SAID Battery Dedicated ISO Standard Cylinder B06-SAID80X75
The AirTAC B06-SAID Battery Dedicated ISO Standard Cylinder B06-SAID80X75 is a genuine double-acting ISO 15552 profile-barrel air cylinder with a Ø80mm bore and 75mm stroke, G3/8 air ports and adjustable end cushioning. Its standardized mounting interface makes it interchangeable with other ISO 15552 cylinders at the mounting interface.
- BoreØ80 mm
- Stroke75 mm
- Port sizeG3/8
- Acting typeDouble acting
- Rod threadM20×1.5
- CushionAdjustable, 36 mm
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac B06-SAID Battery Dedicated ISO Standard Cylinder B06-SAID80X75
The AirTAC B06-SAID80X75 is a double-acting, double-rod ISO 15552 profile cylinder. The B06- prefix marks this as a battery-manufacturing dedicated variant of the SAID80X75, meaning it is mechanically identical to the standard model but designated for cell and pack assembly lines. Because a rod exits both ends, the annulus area is symmetrical, yielding an equal push and pull force of 2268 N at 0.5 MPa.
The twin-rod architecture allows you to drive a primary workpiece from the front while mounting a position flag or cam on the rear rod for external sensing. It uses a PT G3/8 port and a 25mm carbon steel rod. The extruded aluminum barrel features sensor grooves on both sides, though adding a magnet requires the -S suffix to support CMSE reed or DMSE electronic switches.
Airtac B06-SAID Battery Dedicated ISO Standard Cylinder B06-SAID80X75 Technical Specifications
| Model | Airtac B06-SAID Battery Dedicated ISO Standard Cylinder B06-SAID80X75 |
|---|---|
| Series | SAI ISO 15552 profile cylinder |
| Bore size | Ø80 mm |
| Stroke | 75 mm |
| Acting type | Double acting |
| Port size | G3/8 |
| Rod thread | M20×1.5 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 36 mm |
| Max stroke | Up to 1500 mm |
Specifications follow the official AirTAC SAI series datasheet and ISO 15552 dimensions. Confirm against the product label before installation. Port options: G (BSPP) / NPT.
Theoretical Output Force (Ø80mm)
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 2268 N | 2268 N |
| 0.7 MPa | 3175 N | — |
| Max (@1.0 MPa) | 463 kgf | |
Double-rod model: the rod passes through the rear cover, so both piston faces lose rod area and push is shown at the annular-area value. Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
Model Code: Airtac B06-SAID Battery Dedicated ISO Standard Cylinder B06-SAID80X75
| SAI | ISO 15552 profile-barrel cylinder series. |
|---|---|
| 80 | Bore size in mm. |
| ×75 | Stroke length in mm. |
| -S | Optional built-in magnet for sensor position sensing. |
Related SAI-family variants: SAID (double rod), SAIJ (adjustable stroke), SAIL (with lock), SAIF (with valve), BSAI (enclasp / clamp-lock), and SAI-S with built-in magnet. Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B); seals: TPU (blank) / Viton H / NBR N.
Where the Airtac B06-SAID Battery Dedicated ISO Standard Cylinder B06-SAID80X75 Is Used
Battery Cell Stacking
Provides equal force both ways for precise, non-rotating compression of battery cells during stacking and alignment operations.
Twin-Station Transfer
Drives two synchronized tooling stations simultaneously using both rod ends, ensuring parallel movement without phase delay.
Anti-Rotation Guiding
The dual-rod geometry resists torsional loads, keeping battery module handling fixtures perfectly aligned during horizontal transfers.
Is the Airtac B06-SAID Battery Dedicated ISO Standard Cylinder B06-SAID80X75 the Right Cylinder?
Select this 80mm bore when an application demands identical extend and retract dynamics, stepping up from a 63mm bore (1402 N at 0.5 MPa) for heavier battery module handling. A double-rod design is preferred over a single-rod SAI when you need dual-side guidance to prevent rotation or require a rear-rod cam for synchronous secondary actuation. As a direct replacement, it matches standard ISO 15552 mounting dimensions using the Basic, FA, LB, TC, FTC, TCM1, or TCM2 accessory set.
Note that the adjustable air cushions at both ends only decelerate the piston near stroke end; they do not hold the load. If battery stacking or handling operations require position holding without live air pressure, you must integrate an external pilot-operated check valve or specify a BSAID clamp-lock cylinder instead.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Stroke and mounting space
- ✓ Port/thread type (PT/NPT/G)
- ✓ Magnet (-S) for sensors?
- ✓ Side load — consider a guided cylinder
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Avoid side load on the piston rod.
- check Adjust end cushion screws for smooth stops.
- check Use correct mounting accessory (FA/FB/CA/CB/LB/TC).
- check Installation by qualified personnel per AirTAC docs.
Airtac B06-SAID Battery Dedicated ISO Standard Cylinder B06-SAID80X75 FAQ
Because it is a double-rod cylinder, the push and pull forces are identical. It outputs 2268 N in both directions at 0.5 MPa, 3175 N at 0.7 MPa, and 4082 N at 0.9 MPa.
The B06- prefix designates this as an AirTAC battery-manufacturing dedicated cylinder. Mechanically, it is identical to the standard SAID80X75 double-rod ISO 15552 cylinder, featuring the same 80mm bore, 75mm stroke, and PT G3/8 port.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Request a Quote for Airtac B06-SAID Battery Dedicated ISO Standard Cylinder B06-SAID80X75
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.