Airtac B52-GFC Copper-Free Air Source Treatment Component B52-GFC30015LC1W
The AirTAC B52-GFC Copper-Free Air Source Treatment Component B52-GFC30015LC1W is a genuine G-series two-unit air-preparation set: a filter regulator that filters and regulates in one body, coupled to a lubricator. Two bodies do the work of three, with PT1/2" ports, a 5 µm element, a differential-pressure drain and regulation over 0.15 - 0.9 MPa (20 - 130 psi).
- TypeTwo-unit set (F.R. + L.)
- Port sizePT1/2"
- Regulating range0.15 - 0.9 MPa (20 - 130 psi)
- Filtering grade5 µm
- DrainDifferential-pressure drain
- Bowl materialPC
- Pressure gaugeFitted
- ThreadPT
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac B52-GFC Copper-Free Air Source Treatment Component B52-GFC30015LC1W
The AirTAC GFC30015LC1W is a two-unit compressed-air treatment set combining a filter regulator with a separate lubricator for filtration, regulation and oil-mist lubrication in one supply. Two suffixes define this build: L marks the low-pressure regulator type for lines running at a reduced set pressure, and W specifies the finer 5 um filter element in place of the 40 um standard. The C1 suffix adds the external round pressure gauge scaled in MPa. This size 300 unit has a PT1/2 in. port and differential-pressure drain; maximum working pressure is 1.0 MPa (145 psi). Confirm the low-pressure type's adjustment range with us on request.
This is a genuine AirTAC part from the G-series, available in sizes 200 through 600 with 1/8 to 1 in. ports, G (BSPP) or NPT threads, all three drain types, both filter grades and standard or low-pressure regulators. Flow is published as curves rather than a single rating, so ask us to confirm sizing and full datasheet figures on request.
Airtac B52-GFC Copper-Free Air Source Treatment Component B52-GFC30015LC1W Technical Specifications
| Model | Airtac B52-GFC Copper-Free Air Source Treatment Component B52-GFC30015LC1W |
|---|---|
| Series | GFC300 two-unit set |
| Composition | Filter regulator + lubricator (2 units) |
| Port size | PT1/2" (PT thread) |
| Filtering grade | 5 µm |
| Regulating range | 0.15 - 0.9 MPa (20 - 130 psi) |
| Pressure type | Low-pressure type |
| Fluid | Compressed air |
|---|---|
| Max. working pressure | 1.0 MPa (145 psi) |
| Temperature range | -5 to +70 °C (unfreeze) |
| Drain type | Differential-pressure drain |
| Bowl material | PC |
| Pressure gauge | Fitted — round, MPa scale |
| Reflux valve | Not fitted |
Specifications follow the official AirTAC G-series air-preparation data. The regulating band is set by the drain type: automatic and differential-pressure drains regulate 0.15 - 0.9 MPa, a manual drain regulates 0.05 - 0.9 MPa. The low-pressure type adjusts over a lower band than standard; we confirm the exact figures from the factory datasheet. The set has no separate bracket code — the two units couple together with their own mounting hardware. Flow curves, weight and outline dimensions are not published in our data set — ask us and we will confirm from the factory datasheet.
Model Code: Airtac B52-GFC Copper-Free Air Source Treatment Component B52-GFC30015LC1W
| GFC300 | G-series two-unit set, 300 body — sets the port range. |
|---|---|
| 15 | Port size PT1/2". This body offers 08 = PT1/4", 10 = PT3/8", 15 = PT1/2". |
| (blank) | Drain: Differential-pressure drain — this also sets the regulating band (0.15 - 0.9 MPa (20 - 130 psi)). |
| L | Low-pressure type. Blank is standard, L is the low-pressure type. |
| (blank) | Pressure gauge fitted (blank). |
| C | Gauge shape: Round. C is round, F is square. |
| 1 | Gauge scale: MPa. 1 is MPa, 2 is psi, 3 is bar. |
| W | Filtering grade 5 µm. Only 40 µm (blank) and 5 µm (W) exist. |
| (blank) | PT thread. PT is the default; G is BSPP and T is NPT. |
| (blank) | No reverse-flow valve (the default). |
Field order is size, port, drain, type, gauge, shape, scale, grade, thread, reflux — there is no bracket position on a combination set. Constituent units, orderable separately as spares: GFR300-15 filter regulator and GL300-15 lubricator.
Size Class & How It Differs From GC
- GFC200PT1/8" - PT1/4"
- GFC300PT1/4" - PT1/2"
- GFC400PT3/8" - PT1/2"
- GFC600PT3/4" - PT1"
A GFC is two units because filtering and regulating share one body. A GC is three separate units — filter, regulator and lubricator. Both filter, regulate and lubricate; the GFC is the shorter assembly, the GC keeps the filter and regulator serviceable as separate bodies.
| This model | GFC300 · PT1/2" · 5 µm |
|---|---|
| One size down | GFC200 |
| One size up | GFC400 |
| Three-unit equivalent | GC300-15 |
| Build order | Filter regulator first, lubricator last |
Where the Airtac B52-GFC Copper-Free Air Source Treatment Component B52-GFC30015LC1W Is Used
Electronics fixture clamping
Feeding low-pressure clamp and hold-down fixtures on an electronics assembly module, where the 5 um element protects small pilot valves and the lubricator keeps the short-stroke cylinders sealed and smooth.
Instrument air take-off
Supplying air to pneumatic control valves and positioners that require reduced, finely filtered supply: the low-pressure regulator sets the gentle set point while the lubricator is fitted for the actuator circuit.
Test bench conditioning
Conditioning air on an engineering test bench running delicate low-pressure components: clean 5 um air, a controlled reduced pressure read on the round MPa gauge, and oil mist where lubricated motion is under test.
Is the Airtac B52-GFC Copper-Free Air Source Treatment Component B52-GFC30015LC1W the Right Set?
This code brings together the two main decode choices: the L low-pressure regulator type and the W 5 um filter element. Use it when downstream devices need both a reduced set pressure and finer filtration; drop the W for the 40 um standard element or the L for the standard regulator range. Size 300 with a PT1/2 in. port is the G-series mid step - go to 400 or 600 for larger ports, or 200 for smaller. The differential-pressure drain drains automatically at high differential; manual (M) and automatic (A) are options. The round gauge reads in MPa, with other scales and the square gauge available. PT thread is standard; G (BSPP) and NPT are order options.
Flow is published as curves, not a single rated figure, so ask us to confirm sizing against the datasheet before ordering.
Quick checklist
- ✓ Body size for your peak flow (PT1/2" here)
- ✓ Element 40 µm or 5 µm
- ✓ Drain sets the regulating band
- ✓ Gauge fitted, shape and scale
- ✓ Two-unit (GFC) or three-unit (GC) layout
- ✓ Oil mist acceptable downstream
Installation & Maintenance Notes
- check Install with the airflow arrow: filter regulator first, lubricator last.
- check Mount vertically, bowls down.
- check Keep inlet pressure at or below 1.0 MPa (145 psi).
- check Adjust only within 0.15 - 0.9 MPa (20 - 130 psi).
- check Drain condensate before the bowl fills; check the oil level.
- check Keep the set above freezing (-5 to +70 °C, unfreeze).
The PC bowls must not be cleaned with solvents — wipe them with a dry cloth. The lubricator adds an oil mist downstream, so if any branch must stay oil-free, take that branch off before the lubricator or use a GFR300-15 filter regulator on its own.
Airtac B52-GFC Copper-Free Air Source Treatment Component B52-GFC30015LC1W FAQ
Yes - on request. AirTAC publishes G-series flow as characteristic curves rather than a single rated figure, so we do not state one number as a rating. Give us your line pressure, set pressure and demand and we will confirm the sizing from the datasheet.
Two suffixes differ. The L makes this the low-pressure regulator type, for lines needing a reduced set pressure, while F3W is the standard type. The C1 gauge is the external round gauge in MPa, against the embedded square gauge in bar on F3. The W (5 um filter), PT1/2 in. port and differential-pressure drain are common to both.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Related AirTAC Air-Preparation Units
Request a Quote for Airtac B52-GFC Copper-Free Air Source Treatment Component B52-GFC30015LC1W
Send us the quantity, thread type (PT / G / NPT), gauge scale and destination. We confirm price, availability and lead time — usually within 7-8 hours.