AirTAC GF300-10 Filter (GF30010MW)
The AirTAC AirTAC GF300-10 Filter (GF30010MW) is a genuine G-series air filter. It separates condensed water and filters particulate from the compressed-air line through a 5 µm element, with PT3/8" ports and a manual drain. A filter does not set downstream pressure — pair it with a GR regulator, or use a GFR filter regulator, when pressure control is needed.
- TypeAir filter
- Port sizePT3/8"
- Filtering grade5 µm
- DrainManual drain
- Inlet pressure0 - 0.9 MPa (0 - 131 psi)
- Bowl materialPC
- ThreadPT
- BracketMounting bracket included
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the AirTAC GF300-10 Filter (GF30010MW)
GF30010MW is a genuine AirTAC G-series air filter, size 300 with a PT3/8 (3/8 inch) port. It filters only - it removes water and particulate from compressed air, with no regulation and no lubrication. This configuration pairs the finer 5 um filter element (W suffix) with a manual drain, so condensate in the polycarbonate bowl is released by opening the drain valve, and the mounting bracket is included for wall or machine fixing. With the manual drain, maximum inlet pressure is 0 to 0.9 MPa, and the working temperature range is -5 to 70 C (non-freezing).
This is a genuine AirTAC part. The GF family spans sizes 200 to 600 with ports from 1/8 to 1 inch; the same unit is available without the bracket (J suffix) and with the 40 um standard element (drop the W). Flow is published by AirTAC as performance curves rather than a single rated figure, so ask us to confirm sizing and datasheet figures against your application on request.
AirTAC GF300-10 Filter (GF30010MW) Technical Specifications
| Model | AirTAC GF300-10 Filter (GF30010MW) |
|---|---|
| Series | GF300 air filter |
| Port size | PT3/8" (PT thread) |
| Filtering grade | 5 µm |
| Drain type | Manual drain |
| Bracket | Mounting bracket included |
| Fluid | Compressed air |
|---|---|
| Inlet pressure | 0 - 0.9 MPa (0 - 131 psi) |
| Max. working pressure | 1.0 MPa (145 psi) |
| Temperature range | -5 to +70 °C (unfreeze) |
| Bowl material | PC |
| Feature | Low pressure loss |
Specifications follow the official AirTAC G-series air-preparation data. The inlet-pressure band is set by the drain type: automatic and differential-pressure drains run 0.15 - 1.0 MPa, a manual drain runs 0 - 0.9 MPa. Air must not freeze in the unit. Flow curves, weight and outline dimensions are not published in our data set — ask us and we will confirm from the factory datasheet.
Model Code: AirTAC GF300-10 Filter (GF30010MW)
| GF300 | G-series air filter, 300 body — sets the port range. |
|---|---|
| 10 | Port size PT3/8". This body offers 08 = PT1/4", 10 = PT3/8", 15 = PT1/2". |
| M | Drain: Manual drain. Options are differential (blank), automatic (A) or manual (M). |
| (blank) | Mounting bracket included. A bracket ships by default; J orders it without. |
| W | Filtering grade 5 µm. Only 40 µm (blank) and 5 µm (W) exist. |
| (blank) | PT thread. PT is the default; G is BSPP and T is NPT. |
Field order is size, port, drain, bracket, grade, thread — a blank position takes the default. Example: GF300-10AJW is a 300 body, PT3/8", automatic drain, no bracket, 5 µm element, PT thread.
Size Class
- GF200PT1/8" - PT1/4"
- GF300PT1/4" - PT1/2"
- GF400PT3/8" - PT1/2"
- GF600PT3/4" - PT1"
A larger body carries a larger port and passes more air at the same pressure drop. AirTAC publishes flow only as curves, so size the body from your peak demand with headroom rather than from a single rated figure. The GF600 uses an aluminium-alloy bowl; the 200, 300 and 400 bodies use PC.
| This model | GF300 · PT3/8" · 5 µm |
|---|---|
| One size down | GF200 |
| One size up | GF400 |
| Line order | Filter first, then regulator, then lubricator |
Where the AirTAC GF300-10 Filter (GF30010MW) Is Used
Paint spray line conditioning
Installed in the air feed to a paint spray line, using the 5 um element to deliver cleaner air to the spray guns and help protect finish quality.
Process skid actuation supply
Mounted on a process skid frame via the included bracket, filtering the air that drives pneumatic actuators on automated valves.
Robot cell air preparation
Fitted at the air inlet of a robot work cell, conditioning supply air for grippers and end-of-arm pneumatics ahead of the cell's valve manifold.
Is the AirTAC GF300-10 Filter (GF30010MW) the Right Filter?
This code combines the two most common upgrades over the GF30010M: the 5 um element for finer particulate removal against the 40 um standard, and - by not carrying the J suffix - a bracket included for solid mounting. Size 300 with a 3/8 inch PT port is the G-series mid-range; step to size 400 for heavier flow demand or size 200 for compact branches. Drain is manual; automatic (A) and the differential-pressure default are the other choices. Thread is PT as the standard, with G (BSPP) and NPT as catalogue options. Flow is published as curves, not a single rating, so ask us to confirm sizing against your application before ordering.
Quick checklist
- ✓ Body size for your peak flow (PT3/8" here)
- ✓ Element 40 µm or 5 µm
- ✓ Drain: differential, automatic or manual
- ✓ Manual drain caps inlet at 0.9 MPa
- ✓ Thread PT, G (BSPP) or NPT
- ✓ Bracket needed, or order with J
Installation & Maintenance Notes
- check Mount vertically, bowl down, and follow the airflow arrow.
- check Put the filter first in the air-preparation line.
- check Keep inlet pressure within 0 - 0.9 MPa (0 - 131 psi).
- check Drain condensate before the bowl fills.
- check Keep the unit above freezing (-5 to +70 °C, unfreeze).
- check Replace the 5 µm element when pressure loss rises.
The PC bowl must not be cleaned with solvents or exposed to synthetic oils that attack polycarbonate — wipe it with a dry cloth. A filter removes water and particulate only; it does not regulate pressure or add lubrication.
AirTAC GF300-10 Filter (GF30010MW) FAQ
There is no single rated flow to quote: AirTAC publishes flow for the GF series as performance curves. We will confirm the sizing from the datasheet on request - just provide your working pressure and the air demand of the equipment this filter will feed.
Only the filter element grade. The MW version carries the finer 5 um element (W suffix), while the plain M code uses the 40 um standard. Both are size 300 filters with a PT3/8 port, manual drain, included mounting bracket, polycarbonate bowl, 0 to 0.9 MPa maximum inlet and a -5 to 70 C working range. Pick the W code where finer filtration is required.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Request a Quote for AirTAC GF300-10 Filter (GF30010MW)
Send us the quantity, thread type (PT / G / NPT) and destination. We confirm price, availability and lead time — usually within 7-8 hours.